Panasonic TH-86EQ1W Operating Instructions Manual

Also see for TH-43EQ1U: Operating instructions

Contents

Panasonic TH-86EQ1W Operating Instructions Manual Manual pdf 9 page image

9EnglishPrecautions for useCautions when installingDo not set up the Display outdoors.• The Display is designed for indoor use.Install this unit at a location which can support theweight of the unit.• Dropping or falling of the unit may cause injury.Environmental temperature to use this unit• When using the unit where it is below 1 400 m(4 593 ft) above sea level: 0 °C to 40 °C (32 °F to104 °F)• When using the unit at high altitudes (1 400 m(4 593 ft) and higher and below 2 800 m (9 186 ft)above sea level): 0 °C to 35 °C (32 °F to 95 °F)Do not install the unit where it is 2 800 m (9 186 ft)and higher above sea level.• Failure to do so may shorten the life of the internalparts and result in malfunctions.We are not responsible for any product damage, etc.caused by failures in the installation environmenteven during the warranty period.Transport only in upright position!• Transporting the unit with its liquid crystal panelfacing upright or downward may cause damage to theinternal circuitry.Do not grab the liquid crystal panel.• Do not forcibly press the liquid crystal panel, or pushit with a pointed object. Applying a strong force tothe liquid crystal panel will cause unevenness of thescreen display, resulting in malfunction.Do not install the product to a place where theproduct is exposed to direct sunlight.• If the unit is exposed to direct sunlight even indoors,the temperature rise of the liquid crystal panel maycause malfunction.Required space for ventilation• When using the pedestal, leave a space of 10 cm(3 15/16 ”) or more at the top, left and right, and 5 cm(1 31/32 ”) or more at the rear, and also keep the spacebetween the bottom of the display and the tablesurface.If using some other setting-up method (wall-hanging,etc.), follow the manual of it. (If there is no specificindication of installation dimension in the installationmanual, leave a space of 10 cm (3 15/16 ”) or more atthe top, bottom, left and right, and 5 cm (1 31/32 ”) ormore at the rear.)Minimum distance:aa b a: 10 cm(3 15/16 ”)b: 5 cm(1 31/32 ”)a• Operation of this unit is guaranteed up to an ambienttemperature of 40 °C (104 °F). When installing theunit in a case or chassis, be sure to provide adequateventilation with a cooling fan or ventilation hole sothat the surrounding temperature (inside the case orchassis) including the temperature of the front surfaceof the liquid crystal panel can be kept at 40 °C(104 °F) or less.About the screws used when using a wall hangingbracket that conforms to VESA standardsInchmodelScrew pitch forinstallationDepth ofscrew holeScrew(quantity)86 600 mm × 400 mm 16 mm M8 (4)75 600 mm × 400 mm 10 mm M6 (4)65 400 mm × 400 mm 10 mm M6 (4)55 400 mm × 200 mm 10 mm M6 (4)50 400 mm × 400 mm 10 mm M6 (4)43 200 mm × 200 mm 10 mm M6 (4)Note for connectionRemoving and inserting the power cord andconnection cables• When the unit has been installed on the wall, if thepower cord and connection cables are difficult toremove and insert, make connections first beforeinstallation. Be careful not to allow the cables to beentangled. After installation is completed, insert thepower plug to the outlet.When usingBe careful of the movable structure of the powerindicator and remote control sensor.• As factory default, the power indicator and remotecontrol sensor are stored in the main unit. For normaluse, pull out the remote control sensor from the edgeside of the main unit by operating the lever on therear panel. Depending on the setup condition such aswhen using the multi display, store the remote controlsensor in the main unit. (see page 19)Depending on the temperature or humidityconditions, uneven brightness may be observed.This is not a malfunction.• This unevenness will disappear while applying currentcontinuously. If not, consult the distributor.If the Display is not going to be used for anyprolonged length of time, unplug the power supplyplug from the wall outlet.Picture noise may occur if you connect / disconnectthe cables connected to the input terminals youare currently not watching, or if you turn the powerof the video equipment on / off, but it is not amalfunction.