Panasonic TH-42LFP30W Operating Instructions Manual

Also see for TH-42LFP30W: Brochure Specification Operating instructions Service manual

Contents

Panasonic TH-42LFP30W Operating Instructions Manual Manual pdf 50 page image

42Options AdjustmentsItem AdjustmentsInput lockLocks the input switch operation.Off VIDEO Component/RGB PC DVI HDMI1 HDMI2 OffNotes:• Only the adjusted signal is displayed (see page 15).• Input switch can be used when this is set to “Off”.Button lockOff On MENU&ENTEROff: All the buttons on main unit can be used.MENU&ENTER: Locks and buttons on main unit.On: Locks all the button on main unit.Sets Button lock with the unit buttons in the following procedure.Off: Press four times→Press four times→Press four times→PressMENU&ENTER: Press four times→Press four times→Press four times→PressOn: Press four times→Press four times→Press four times→PressRemocon User levelOff User1 User2 User3Off: You can use all of the buttons on the remote control.User1: You can only use , , , , buttons on the remote control.User2: You can only use button on the remote control.User3: Locks all the buttons on remote control.Off-timer functionEnable: Enables the “Off-timer function”.Disable: Disables the “Off-timer function”.Note: When “Disable” is set, the Off-timer is cancelled.Initial Power ModeNormal On StandbySets the power mode of the unit for when the power recovers from failure or after plugging off and in again.Normal: Power returns in as the same state as before the power interruption.Standby: Power returns in standby mode. (Power Indicator : red/orange)On: Power returns in power On. (Power Indicator : green)Note: When using multiple displays, “Standby” is preferred to be set in order to reduce a power load.Power On ScreenDelayOff 1 2 3.... 30You can set the power-on delay time of the displays to reduce the power load, when you press toturn on the multiple displays that are set together, for example, on MULTI DISPLAY system.Set each display’s setting individually.Off: The display will be turned on at the same time as is pressed.1 to 30 (sec.) : Set the power-on delay time (second).After pressing , the display will be powered on with time delay depending on this setting.Notes:• During this function is working, the power indicator is blinking green.• This function also works when the power recovers from failure or after plugging off and in again the power cord.Clock DisplayOff: Not display the clock.On: Display the clock.The clock is displayed at the lower left of the screen when button is pressed.Note: When “PRESENT TIME Setup” is not set, the clock is not displayed evenif “Clock Display” is “On”. (see page 27)Power On Message(No activity poweroff)Whether to show/hide No activity power off Precautions at the time of power ON is set.On: The warning precautions are shown at the time of power ON.Off: The warning precautions are not shown at the time of power ON.Note: This setting is enabled only if “No activity power off” is “Enable” (see page 31).Winter ModeSet this function to maintain the image quality when the product is used in a low temperatureenvironment of 39 °F/4 °C or lower.Off: Normal standby operationOn: Image is muted at standby and backlight is turned on when the inside temperature of the displayis 32 °F/0 °C or lower to prevent decreasing the temperature. Backlight is turned off when theinside temperature is 50 °F/10 °C or higher.When this function is set to “On”, the following message appears at standby.Notes:• Do not unplug the power cable while using the product with this function “On”.• When this function is set to “On”, the power consumption at standby is approx. 100 W.• Turn this function “Off” to use this product in an environment of 39 °F/4 °C or higher.Power Switch LockSets the lock setting for the display Power switch.On: Power switch operation is disabled.Off: Power switch operation is enabled.Winter mode is active.10:00