PANASONIC FIRE ALARM SOLUTIONSDAILY USER´S MANUALEBL128 VERSION 2.2.X

INTRODUCTION

DESCRIPTION OF THE FRONT

LED INDICATORS

PUSH BUTTONS

ACCESS LEVELS

NAVIGATION / GENERAL PROCEDURES

PERFORM MONTHLY TEST (H1)

DISABLE OR RE-ENABLE (H2)

SET CALENDER AND CLOCK (H3)

PRESENT SYSTEM STATUS (H4)

FAULT ACKNOWLEDGE (H6)

PERFORM ZONE TEST (H7)

INTERLOCKING OUTPUTS AND INPUTS (H9)

Panasonic EBL128 Daily User's Manual

fire alarm system

technical data

EBL128

operating instructions

Revision

Definitions / Explanations

Old detector

Control panel (CP)

Overview

Control & Indicating Equipment

LED indicators and push buttons

Normal operation

Access levels

Access level 1

Access level 2B

Access level 3A

Access level 4

Silence Alarm devices

New Zealand FB Silence switch (outside switch)

Disable / Re-enable alarm devices

Silence buzzer

ventilation outputs

Evacuate

German functions / units

Indication "Brandfall Steuerungen ab

Indication "ÜE ab

Door open

Technical address / Presentation number

Alarm types

Fire alarm

Fire alarm menu (X1-X9)

Alert Annunciation alarm (AA alarm)

Co-incidence alarm (two-unit / -zone dependence)

Key cabinet alarm

Key cabinet opened in conjunction with a fire alarm

Alarm Acknowledgement Facility (AAF)

Alarm reset

Alert Annunciation

Heavy smoke / heat alarm reset

Acknowledged alarm

Fault

Fault messages

Fault acknowledge

Commissioning an EBL128

SSD programming & download

Download of Alarm texts

Software (S/W) download

Earlier S/W version download

Restart

Boot menu

Access

Perform monthly test (H1)

Disable or re-enable (H2)

Disable zone / address (H2/B2)

Disable output (H2/B3)

outputs (H2/B4)

Re-enable zone (H2/B5)

Re-enable zone / address (H2/B6)

Re-enable output (H2/B7)

device outputs (H2/B8)

Disable or re-enable outputs for routing equipment (H2/B9)

De-activate alert annunciation function (H2/B10)

Set calendar and clock (H3)

Daylight saving time

Present system status on display (H4)

Disablement by time channel (H4/U2)

Sensor values (H4/U3)

Reset of a week average sensor value

Sensors activating SERVICE signal (H4/U4)

Event log (H4/U5)

Show configuration and alarm counter (H4/U6)

Service (H5)

Access code for service and maintenance

Disconnect / Re-connect COM loop (H5/A1)

Disconnect / Re-connect zone line input (H5/A2)

Calibration of supervised outputs (H5/A3)

Sensitive fault detection mode (H5/A4)

Service mode for COM-loop (H5/A5)

Show information about Site Specific Data (H5/A6)

Display current consumption on COM loop (H5/A7)

Display statistics for COM loop (H5/A8)

Activate address setting mode for DU (H5/A9)

Acknowledge FAULTS (H6)

Perform ZONE TEST (test mode) (H7)

Maintenance (H8)

Acknowledge SERVICE signal (H8/S1)

Restore weekly average to default (H8/S2)

Test of alarm devices (H8/S3)

Safe shut down of control unit (H8/S4)

Activate address in alarm mode (H8/S5)

Change access code for service and maintenance (H8/S6)

Change access code for PC-communication (H8/S7)

Interlocking outputs and inputs (H9)

Activate interlocking output (H9/C2)

Reset interlocking output (H9/C3)

Disable interlocking output (H9/C4)

Re-enable interlocking output (H9/C5)

Change access code for daily duties (H10)

COM loop

A single break (cut-off) on the COM loop

Several breaks (cut-offs) on the COM loop

Short-circuit on the COM loop

Programmable relay output (R0)

V DC power supply outputs

internal power supply

Expansion boards 458x

Expansion board address setting

Input states

Inputs and outputs expansion board 4583

Generic

Fan control

Peripheral devices

Addressable I/O units

Alarm devices (addressable sounders)

Short circuit isolators (addressable)

Units for Hazardous (Ex) areas

detectors

Units connected to the RS485 interface

Alert Annunciation Units

External Presentation Units

German Fire Brigade Panels

Units connected to the RS232 interface J5

Other units

Alarm devices (sounders, etc.)

Programmable inputs

Control unit Input I0 & Inputs and Outputs exp. board

Input programming

Logic

Not supervised (default)

Programmable outputs

Control unit outputs S0 – S1

Control unit output R0

The 3361 unit outputs Re0 – Re1

Output programming

Supervised

Control expression

Logical operators

Interlocking function

Interlocking indications

Fire Door Closing function

Functions / Services / Features

Decision value

Alarm algorithm / Alternative alarm algorithm

Filtering algorithm

Smouldering smoke algorithm

Performance factor

Class A1 algorithm

Self verification

Two-zone dependence (co-incidence alarm)

Delayed alarm

Quiet alarm

Fire alarm type B

Disable zone

Disconnect / Re-connect COM loop

Calibration of supervised outputs

Alarm texts

Downloading texts to the EPU 1728, AAUs

Time channels 1-4

Loss of main power source

Special New Zealand functions

Battery faults

FAULT: Low battery capacity

Cyber sensor functions

Pulse up – down counter

Learning function / Learning conditions

Learning conditions

Alarm delay time

Analog data output

Self diagnosis of internal devices

Control unit properties (settings)

Control Unit Properties

Time Channels

Alarm Algorithms

Parameters for smoke algorithms

National Holidays

Output Signal Periods

Advanced

Zone line input alarm delay time

Statistics

Cable types

com loop cable length

current consumption

Current consumption

Charger functions

Battery charging functions

Panasonic EBL128 Daily User's Manual

Product

Learn More

Legal


Contents Table Of Contents INTRODUCTION DESCRIPTION OF THE FRONT LED INDICATORS PUSH BUTTONS ACCESS LEVELS NAVIGATION / GENERAL PROCEDURES PERFORM MONTHLY TEST (H1) DISABLE OR RE-ENABLE (H2) SET CALENDER AND CLOCK (H3) PRESENT SYSTEM STATUS (H4) FAULT ACKNOWLEDGE (H6) PERFORM ZONE TEST (H7) INTERLOCKING OUTPUTS AND INPUTS (H9)	PANASONIC FIRE ALARM SOLUTIONSDAILY USER´S MANUALEBL128 VERSION 2.2.X Next / 18