Panasonic BB-HCM705A - Fixed MP H.264 Dome POE Indoor Network Camera Installation Manual

Also see for BB-HCM701: Comparison chart Important information

Contents

Panasonic BB-HCM705A - Fixed MP H.264 Dome POE Indoor Network Camera Installation Manual Manual pdf 2 page image

2Camera DiagramConnectionsBefore proceeding, confirm that your PC is connected to your router and can access the Internet. Also confirm that your router’s UPnP ™ feature is enabled.(Most routers have UPnP™ turned off by default.) Refer to the operating instructions included with your router or to the Panasonic Network Camera website(http://panasonic.net/pcc/ipcam/) for more information.Connect the camera to your PoE hub using a LAN cable (Cat-5 straight cable) as described below.Connect the camera to your router and the power outlet as described below.Front View Rear View Side ViewABCDECamera coverMicrophoneIndicator *1LensLens coverFGHIJKSafety wire holeLAN portDC IN jackExternal INPUT interfaceSerial number andMAC address labelCable hookLMNORESTART buttonSD memory card slotFACTORY DEFAULT RESETbuttonFUNCTION button/indicator*1 See 1.1 Understanding the Camera Indicator in the Troubleshooting Guide on the CD-ROM for indicator meaning.When connecting the camera using PoE (Power over Ethernet)1 Connect a LAN cable to the camera and to the PoE hub.• Your PoE hub must be connected to the router. Refer to the operatinginstructions included with the PoE hub for connection instructions.2 Connect a LAN cable to a LAN port of the PoE hub and to a LAN port of therouter.• Confirm that the indicator lights green after about 1 minute. If theindicator does not light green, see 1.2 Camera Indicator Issues in theTroubleshooting Guide on the CD-ROM.• Use a 4-pair UTP/STP cable.• Do not use a relay connector or a hub between the camera and the PoEhub. These devices may disturb the data or electricity transmission.• If the PoE hub has indicators, the indicator lights as shown in the tablebelow.Indicator DescriptionLINK Turns on when the data is transmitted from the camera.PoE Turns on when the electricity is supplied to the camera.• If the PoE hub is turned off or power supply is temporarily cut off by thedisconnection of the LAN cable, it may take time for the PoE hub’sindicators to light.• The indicator display differs depending on manufacturers, refer to themanuals of the PoE hub.Caution• The camera is to be connected only to PoE networks without routing tothe outside plant.When connecting the camera using the AC adaptor (Optional)• If using an AC adaptor, use only the optional Panasonic AC adaptor.1 Connect the LAN cable to the camera and the router.2 Connect the AC adaptor cord to the DC IN jack.3 Connect the AC cord to the AC adaptor, then plug the ACcord into the power outlet.• Confirm that the indicator lights green after about1 minute. If the indicator does not light green, see 1.2Camera Indicator Issues in the Troubleshooting Guideon the CD-ROM.• When you operate the camera, the power outlet shouldbe near the camera and easily accessible.• Use only specified Panasonic AC adaptor (Model No.BB-HCA7A, BB-HCA7CE, BB-HCA7E).After the camera’s indicator turns green, you may set up the camera. Continue by following the procedure described in theincluded Setup Guide.• If the indicator does not turn green, see 1.2 Camera Indicator Issues in the Troubleshooting Guide on the included CD-ROM.Read the following information after setting up the camera according to the procedure described in the Setup Guide.FG H I J KABCDEL MN OPCLAN cable(Cat-5 straight cable)PoE indicatorLINK indicatorTo the powersupplyPoE hubRouterModemInternetGreenTo thepoweroutletLAN cable(Cat-5 straight cable)AC cordAC adaptor(BB-HCA7A, BB-HCA7CE,BB-HCA7E)RouterModemInternet PCGreen

/ 4

Related manuals for Panasonic BB-HCM701