Panamax MX5102 Instructions Manual

Also see for MX5102: Specifications Instruction manual

Contents

Panamax MX5102 Instructions Manual Manual pdf 3 page image

This manual contains important instructions that should be followed dur-ing installation and maintenance of the UPS and batteries.Please read and follow all instructions carefully during installationand operation of the unit. Read this manual thoroughly before at-tempting to unpack, install, or operate.CAUTION! Risk of explosion if battery is replaced ay an incorrect type.CAUTION! The UPS must be connected to an AC power outlet with fuse orcircuit breaker protection.DO NOT plug the machine into an outlet that is not grounded. If you need tode-energize this equipment, turn off and unplug the UPS.CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT!Panamax does not sell products for life support or medical applications. DONOT use in any circumstance that would affect operation or safety of any lifesupport equipment, with any medical applications, or patient care.CAUTION! The battery can energize hazardous live parts inside even whenthe AC input power is disconnected.CAUTION! To prevent the risk of fire or electric shock install in a temperatureand humidity controlled indoor area, free of conductive contaminants. (Pleasesee specifications for acceptable temperature and humidity range).2Important Safety InstructionsCAUTION! To reduce the risk of electric shock, do not remove the cover. Nouser serviceable parts inside.CAUTION! To avoid electrical shock, turn off the unit and unplug it from theAC power source before servicing the battery or installing a component.CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS!To reduce the risk of fire, do not use with or near aquariums. Condensationfrom the aquarium can come in contact with metal current contacts andcause the machine to short out.Note: AC Power management devices, such as a UPS, have certain limita-tions with regard to reactive loads and wattage. The MX5102 has a handlingcapacity of 600VA or approximately 600 watts. Excessive power consump-tion beyond these specifications can affect battery life and performance.For pluggable equipment, the socket shall be installed near the equipmentand shall be easily accessible.CAUTION: To reduce the risk of fire, connect only to a circuit provided witha 20 amperes maximum branch circuit overcurrent protection in accordancewith National Electric Code, ANSI / NFPA 70.To avoid electrical shock, a screwdriver must be used to remove screws toopen battery cover before replacing battery. Must close battery compartmentusing screwdriver to tighten screws.NOTE TO CATV INSTALLERSThis reminder is provided to call attention to Article 820-40 of theNEC. That article provides specific guidlines for proper grounding. Itspecifies that the cable ground shall be connected to the groundingsystem of the building and as close to the point of entry as practical.FCC NoticeFCC NoticeThis equipment has been tested and found to comply with the limits fora Class B Digital Device, pursuant to Part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmfulinterference in residential installation. This equipment generates, uses,and can radiate radio frequency energy and, if not installed and usedin accordance with the instructions, may cause harmful interference toradio communications. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be de-termined by turning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the following measures:(1) Reorient or relocate the receiving antenna.(2) Increase the separation between the equipment and receiver.(3) Connect the equipment into an outlet on a circuit different from thatto which the receiver is connected.(4) Consult the dealer or an experienced radio/TV technician for help.Any special accessories needed for compliance must be specified in theinstruction.CAUTION: A shielded-type power cord is required in order to meet FCCemission limits and also to prevent interference to the nearby radio andtelevision reception. It is essential that only the supplied power cord beused. Use only shielded cables to connect I/O devices to this equipment.CAUTION: Any changes or modifications not expressly approved by theguarantee of this device could void the user’s authority to operate theequipment.