Panamax MAX 4310 Instructions Manual

Also see for MAX 4310: Instructions

Panamax MAX 4310 Instructions Manual Manual pdf 1 page image

INSTRUCTIONS MAX® 4310Thank you for choosing Panamax . TheMAX® 4310 is designed to provide maxi-mum protection for audio/video equipmentwith external signal connections such ascable TV, rooftop antenna and DBS satellitesystems.INSTALLING THE MAX® 4310NOTE: The MAX® 4310 and the connectedequipment must be indoors and in the samebuilding.AC Installation1. Plug the MAX® 4310 directly into a prop-erly grounded 3-wire AC outlet*.2. Turn the MAX® 4310 on.3. Plug in one of the pieces of equipmentyou want to protect and turn the equipment on.If the equipment is working correctly, contin-ue to plug in and turn on your equipment. Inthe extremely unlikely event that everythingdoes not work perfectly, stop and read thetroubleshooting section. If you continue tohave problems, call PANAMAX CustomerRelations Department at 800-472-5555, USAand Canada.*Many old buildings are inadequately wired.It is very common for a building to beimproperly grounded. Building wiring andgrounding must conform to applicable NEC(USA) or CEC (Canada) codes for the PANA -MAX connected equipment policy to be valid.Note to CATV Installer:This reminder is provided to call the atten-tion to Article 820-40 of the NEC. That articleprovides specific guidelines for propergrounding. It specifies that the cable groundshall be connected to the grounding systemof the building and as close to the point ofcable entry as practical.Satellite Coax Installation **1. Connect the coax cable from the satellitedish to a Satellite coax terminal on theMAX® 4310.2. Connect the provided coax jumper cableto the other Satellite coax terminal on theMAX® 4310.3. Connect the other end of the coax jumpercable to the input jack on your satellitereceiver.Cable TV or Rooftop Antenna Coax Installation **1. Connect the coax cable from the wall orfloor plate to a CATV/ANT coax terminal onthe MAX® 4310.2. Connect the provided coax jumper cableto the other CATV/ANT coax terminal on theMAX® 4310.3. Connect the other end of the coax jumpercable to the input jack on your television,VCR, or satellite receiver.**There is no designated input or output jack for theMAX® 4310 Satelliteand CATV/ANT coax terminals.The coaxial protection circuitry is bi-directional inboth signal transmission and protection capabilities.Phone Installation1. Connect a phone cable from the wall jackto the LINE terminal on the telephone jack onthe MAX® 4310.2. Connect the provided phone line cablefrom the EQUIP terminal on the MAX® 4310to the input jack on your satellite receiver.Please note that the protection circuitr ywill not work if these lines are reversed.Rack MountingAn optional rack mount kit is available.Order # GRM2205.TROUBLESHOOTINGThere is no AC power to my equipment, ormy equipment doesn’t turn on.Make sure that the MAX® 4310 is pluggedinto a working AC outlet. Check all ACconnections.Make sure the MAX® 4310 and connectedequipment is turned on. If you are using the12VDC trigger, make sure that the source isactually supplying the voltage needed toactivate the MAX® 4310.Check to see if the circuit breaker on theMAX® 4310 needs to be reset (press in).The MAX® 4310 circuit breaker disconnectsAC power from the connected equipment.You have exceeded the ampere rating foryour surge protector. As a temporary fix, dis-connect one or more pieces of equipment.Ask your dealer about additionalPANAMAX products that may be required.There is no picture or sound on my TV .Check the coaxial connections, making surethat they are correctly and securely installed.Ensure that the TV set is plugged into a pow-ered AC outlet.When running the DBS system test, theDBS connection displays as failed.Check the appropriate connections to ensurethat they are correctly and securely installed.If you continue to have trouble with yourMAX® 4310 or this section has not fixed theproblem, please call PANAMAX CustomerRelations Department at 800-472-5555.CONTACTING PANAMAXFor product and warranty information,dealer information, and other generalinformation contact Customer Relationsat:Email: custrelations@panamax.comWeb: www.panamax.comFax: 707-283-5901Phone: 800-472-5555or 707-283-5900,7:30 a.m.- 5 p.m.PSTMAX® 4310 PRODUCT SPECIFICATIONSAC Surge ProtectionLine Voltage……………......……………….120V, 50/60 HzMaximum Current Rating…….......................………….15AUL 1449 Surge Suppression Rating…...................……330VProtection Modes…………………….......…..L-N, L-G, N-GInitial Clamping Level………........….200V Peak, 141V RMSResponse Time………...........................……………...<1nsJoule Rating……………………............………1650 JoulesPeak Impulse Current……...........................………52,000AEMI/RFI Noise Filtration……......…. 50dB (100KHz - 1 MHz)Catastrophic Surge Circuit……......................………….YESThermal Fusing……...................……………………….YESOver/Under Voltage Protection……....................………YESOver-voltage shutoff threshold…………..............…147V ±8Under-voltage shutoff threshold……..................……84V±6DC TriggerConnection………………….............……3.5mm mini-plugVoltage and Polarity……..................5-30VDC, bi-directionalCurrent Requirement….......................……………>10mASatellite CircuitClamping Level………...........................……………….27VAttenuation……..................…<1 dB from 950MHz - 2.2GHzShielded……........................................………………..YESConnections……..........……………Gold plated, Female “F”CATV/ANT CircuitClamping Level……..................................…………….0.7VAttenuation………….........……<1 dB from 5MHz - 950MHzShielded……….................................………………….YESConnections…………………......…Gold plated, Female “F”Telephone CircuitClamping Level…….....................................………….260VCapacitance………………….....................…30pf (approx.)Suppression Modes…….......………Metallic & LongitudinalWires Protected…………......……….2 wire/ 1pr. (Pins 4,5)F u s e l e s s / A u t o - R e s e t t i n g … … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . … … Y E SConnections…………........................……………RJ-11/45INS4310 REV. A 11/0215A Circuit Breaker - willautomatically “open”when the current load isgreater than 15 Amperes.When this happens, thecircuit breaker can bemanually reset by simplypushing the reset button,which will have “popped”out.”Always-On Outlets -Three Always-On,Balanced L Filtered out-lets provide a constantpower source for pro-grammable analog ordigital equipment.Switched Outlets -Four BalancedL Filtered outletscontrolled by oneof the two triggersources.Voltage Sense TriggerInput - 3.5mm Mini-Plugjack. Connect to a remotetrigger device that pro -vides 12VDC to trigger astartup/ shutdownsequence. This is the sec-ond trigger that will turn-on or turn-off theswitched outlets.Telephone Jacks -In/Out connectionsfor telephone lineor pay-per-viewline protection.Satellite Coax Jacks - Two pair ofgold plated F-connectors optimizedfor Satellite TV signal line protection.Cable TV Coax Jacks -Single pair of goldplated F-connectorsoptimized for Cable TVand Rooftop Antennasignal line protection.Switched Outlets pushbutton -one of two triggers that canturn-on or turn-off the switchedoutlets. Leave this switch in theON position if the DC trigger isbeing used.Switched Outlets LED -(green) indicates the sta-tus of the “SwitchedOutlets” pushbutton andcorresponds with theswitch position.Ground OK LED - (green)indicates that the walloutlet is properly grounded.Ground Fault LED - (red)when lit, indicates that thewall outlet is improperlywired.Unsafe Voltage LED - (red) whenlit, indicates that incoming volt-ages are unsafe and the surgeprotector has disconnected thepower to protect your equipment.Always-on Convenience Outlet -10 Ft. AC Power Cord -1690 Corporate Circle, Petaluma, 94954 • Phone 707-283-5900 • Toll Free 800-472-5555 • Fax 707-283-5901 • www.panamax.com

/ 1

Related manuals for Panamax MAX 4310