Ochsner AIR 7 Operating And Installation Manual

Contents

Ochsner AIR 7 Operating And Installation Manual Manual pdf 3 page image

982000-AIR-M2-M4-EN03.1 | www.ochsner.com 3CONTENTSPLEASE NOTEOPERATION1. Information on documentation 41.1 Safety information 41.1.1 Arrangement of safety information 41.1.2 Symbols and possible dangers 41.1.3 Keywords 41.2 Other symbols 51.3 Units of measurement 51.4 Specified performance data 52. Safety 52.1 Intended use 52.2 General safety information 53. Appliance description 63.1 Functionality 63.2 Appliance components 63.2.1 Indoor unit 63.2.2 Outdoor unit 73.2.3 Heat pump control unit 73.3 Name plate 74. Activating settings 84.1 Operating costs 84.1.1 Flow temperatures 84.1.2 Ventilation 84.1.3 Heating setback program 95. Maintenance and care 96. Problem solving 9INSTALLATION7. Safety 107.1 General safety information 107.2 Regulations, codes and standards 108. Appliance description 108.1 Standard delivery 108.2 Hydraulic variants of the indoor unit 119. Preparing to install the appliance 139.1 Indoor unit installation location 139.1.1 Keep minimum clearances 139.2 Outdoor unit installation location 139.2.1 Keep minimum clearances 149.3 Foundations for the outdoor unit 149.3.1 Laying spot foundations 159.3.2 Laying strip foundations 169.3.3 Installing on flat roofs 169.4 Preparing the refrigerant lines 179.4.1 Line lengths 189.4.2 Pipe diameter 189.4.3 Preparing the wall outlets 199.4.4 Preparing refrigerant lines passing through open air209.4.5 Preparing underground refrigerant lines 209.5 Preparing the electrical connections 229.5.1 Heat pumps for three-phase alternating current 229.5.2 Heat pumps for single phase alternating current 239.5.3 Cables from main distributor to indoor unit 239.5.4 Cables from indoor to outdoor unit 239.5.5 Temperature sensor 239.5.6 Pumps and servomotors (230 VAC) 249.5.7 PSU signal contact 249.5.8 Smart Grid 2410. Appliance installation 2510.1 Installation of indoor unit 2510.1.1 Delivery and transportation 2510.1.2 Positioning the appliance 2610.1.3 Disassembling the appliance casing 2610.1.4 Assembling the appliance casing 2710.2 Installing the outdoor unit 2810.2.1 Delivery and transportation 2810.2.2 Positioning the appliance 2910.2.3 Disassembling the appliance casing 2910.2.4 Installing the snow cover 2910.2.5 Fitting the cylindrical silencer 2910.2.6 Installing the SSP snow cover 3010.3 Connecting the heat sink system 3110.3.1 Connecting the heating water 3110.3.2 Safety valve drain 3210.3.3 Filling the heating system 3210.3.4 Diaphragm expansion vessel (DEV) 3310.3.5 Flow metering 3310.3.6 Cooling version 3310.3.7 Connecting the DHW 3310.4 Electrical connection 3410.4.1 General 3410.4.2 Electrical connection of the indoor unit 3410.4.3 Electrical connection of the outdoor unit 3610.5 Connecting heat source system 3710.5.1 Connecting the refrigerant lines 3710.5.2 Checking for leak tightness 3810.5.3 Filling the refrigerant circuit with refrigerant 3810.5.4 Insulating the refrigerant lines 3811. Commissioning 3911.1 Before switching on for the first time 3911.2 Testing the control circuit 3911.3 Adjusting the flow rate 3911.4 Heat generator pump (HGP) 4211.5 Necessary conditions for commissioning 4311.6 Commissioning the system 4411.7 Decommissioning 4512. Troubleshooting 4612.1 Fault messages on the master controller 4612.2 Reset high limit safety cut-out 4813. Appliance maintenance 4813.1 Testing safety valve 4813.2 Maintenance contract 4914. Specification 5014.1 Heat pumps for three-phase alternating current 5014.1.1 Data table 5014.1.2 Output diagrams 5414.1.3 Details of energy consumption 6014.2 Heat pumps for single phase alternating current 6214.2.1 Data table 6214.2.2 Output diagrams 6414.2.3 Details of energy consumption 6614.3 Limits of use 6714.4 System schematic diagrams 6814.5 Voltage quality in island mode 8414.6 Dimensions and connections 8514.6.1 Indoor unit 8514.6.2 Outdoor unit 8615. Environment and recycling 9016. Declaration of Conformity 9117. ERP-Data 93