NEC MultiSync V801 User Manual

Also see for MultiSync V801: Manual Manual Specification Manual Installation guide

NEC MultiSync V801 User Manual Manual pdf 27 page image

English-25EnglishLAN SETTING When you use this function, EXTERNAL CONTROL should be “LAN”.NOTE: When changing the LAN SETTING, you need to wait several seconds until the LANSETTING is applied.DHCP Enabling this option automatically assigns an IP address to the monitor from your DHCP server.Disabling this option allows you to register the IP address or subnet mask number obtained fromyour network administrator.NOTE: Consult your network administrator for the IP address when “ENABLE” is selected for[DHCP].DISABLEIP ADDRESS Set your IP address of the network connected to the monitor when “DISABLE” is selected for[DHCP].192.168.0.10SUBNET MASK Set your subnet mask number of the network connected to the monitor when “DISABLE” isselected for [DHCP].255.255.255.0DEFAULT GATEWAY Set your default gateway of the network connected to the monitor when “DISABLE” is selectedfor [DHCP].192.168.0.1DNS PRIMARY Set your primary DNS settings of the network connected to the monitor. 0.0.0.0DNS SECONDARY Set your secondary DNS settings of the network connected to the monitor. 0.0.0.0SETTING COPY In a daisy chain scenario, select the OSD menu categories that you want to copy over to theother monitor.NOTE: When you use this function, EXTERNAL CONTROL should be “RS-232C”. This functionresets to default when power is off. This function has a limit depending on the cable you use.NOCOPY START Select “YES” and press the SET button to start copying.ALL INPUT All input terminals settings are copied when you select this item. Default is off.RESET Resets “MULTI DISPLAY” options back to factory settings except LAN SETTING and TILEMATRIX MEM.-DISPLAY PROTECTIONPOWER SAVEPOWER SAVE Sets how long the monitor waits to go into power save mode after the signal is lost.Note: When connecting DVI, the video card might not stop sending the digital data eventhough the image might have disappeared. If this occurs the monitor will not switch into powermanagement mode.ONAUTO STANDBY ON: Monitor automatically goes into OFF mode 10 minutes after signal is lost.OFF: Monitor does not automatically go into OFF mode even after signal is lost.NOTE: This function is disabled when RGB, VIDEO or OPTION POWER are enabled.OFFHEAT STATUS Displays status of the FAN, BACKLIGHT and TEMPERATURE. -FAN CONTROL Cooling fan reduces the temperature of the display to protect from overheating.If “AUTO” is selected, you can adjust the start temperature of the cooling fan and fan speed.AUTOSCREEN SAVER Use the SCREEN SAVER function to reduce the risk of Image Persistence.GAMMA The display gamma is changed and fi xed when “ON” is selected. OFFBACKLIGHT The brightness of backlight is decreased when “ON” is selected.NOTE: Do not select this function when picture mode is AMBIENT1 or AMBIENT2.OFFMOTION The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) atuser determined intervals. You can set interval time and zooming ratio.This function is disabled when PIP, STILL, TEXT TICKER or TILE MATRIX are enabled.OFFSIDE BORDER COLOR Adjusts the color of the side borders when a 4:3 image is displayed.Press + button, the bar will become lighter.Press - button, the bar will become darker.15AUTO BRIGHTNESSDPORT, DVI, VGA, RGB/HV inputs onlyAdjusts the brightness level according to the input signal.NOTE: Do not select this function when picture mode is AMBIENT1 or AMBIENT2.OFFCHANGE SECURITYPASSWORDAllows the security password to be changed.The factory preset password is 0000.-SECURITY Locks the security password. OFFDDC/CI ENABLE/DISABLE: Turns ON or OFF the two way communication and control of the monitor. ENABLEALERT MAIL Selects whether or not to send an e-mail notifi cation of monitor error via wired LAN. OFFRESET Resets the following settings within the DISPLAY PROTECTION menu back to factory setting:FAN CONTROL, SCREEN SAVER, SIDE BORDER COLOR, AUTO BRIGHTNESS, DDC/CI.-