NAD T785 HD Owner's Manual

Also see for T785: Catalog Specification sheet Owner's manual Specifications Owner's manual

NAD T785 HD Owner's Manual Manual pdf 18 page image

SETUP MENUThe Setup Menu allows one to customize the operation of the T 785 to the ancillaryequipment used in one’s specific AV system. Unless your system exactly matchesthe factory defaults as shown in the accompanying Quick Start Guide, you will needto use the setup menu to configure the inputs of the T 785.At Setup Menu, the following are configurable – Video Setup, Source Setup,Speaker Setup, Zone Setup, Amplifier Setup, Trigger Setup, Listening ModeSetup, Display Setup and A/V Presets.To access and navigate through Setup Menu and its sub-menu selections,please refer to and follow the directions stated in the sections ‘Display theOSD’ and ‘Navigating the OSD and Making Changes.’VIDEO SETUPThis menu allows you to set the display resolution of the T 785 along withcorresponding frame rate and aspect ratio.Resolution: The T 785 has the excellent ability to upconvert standarddefinition video contents to high definition video signal. Depending uponyour TV/Monitor’s resolution capabilities, select the applicable resolutionsettings - Auto, 480i, 480p, 576i, 576p, 720p, 1080i and 1080p.When “Auto”is selected, the T 785 automatically selects the connected TV/Monitor’shighest compatible resolution.Note that if the display is connected to Composite or S-Video Monitor OUT,the video output resolution must be set to 480i or 576i to view content.Frame Rate: The frame rate is the number of times per second that ascreen image is refreshed. Depending upon your area and video resolutioncapability of your TV/Monitor, the following “Frame Rate” options areavailable (Note that frame rate is output resolution dependent; not all framerate settings are selectable for the various resolution levels).50Hz: Setting normally for Europe and most of Asia. For resolutionsettings 576i and 576p, 50Hz is the only available option.60Hz: Setting normally for North America. For resolution settings 480iand 480p, 60Hz is the only available option.24Hz: Select to deliver film-like motion characteristics. “24Hz” isselectable only at 1080p resolution setting.Aspect Ratio: Select a picture size matching the aspect ratio of yourTV/Monitor.4:3: Select “4:3” when a standard 4:3 TV is connected. “4:3” is not selectablewhen the resolution is set to higher that 480i, 480p, 576i or 576p.16:9: Select “16:9” when a 16:9 wide TV is connected. “16:9” is the onlyavailable option when the resolution is set to 720p, 1080i or 1080p.After making changes in “Resolution”, “Frame Rate” or “Aspect Ratio”, scrolldown to “Apply Changes” and press [ ] to implement the settings. A newOSD prompt will appear as belowPress the [ ] to apply the new resolution or [ ] to return to the currentresolution. If [ ] is selected, you will be prompted again to another OSDprompt as belowPress [ ] to save the new resolution or [ ] to cancel the change inresolution. If you do not press either [ ] or [ ] and let the timer elapse,the new resolution will not be implemented and the current resolutionsetting remains.IMPORTANT NOTEIf you inadvertently selected a resolution setting (like 1080p) that yourTV/Monitor does not support, the video display will go blank. To restorevideo display, press and hold both front panel buttons LISTENING MODEand TONE DEFEAT and then release both buttons - the VFD and OSD willboth show “Video Reset”. Both the “Picture Controls” and “Video Setup”settings will be restored to their factory defaults after Video Reset.NOTES· When using component video output, a standard definition video canbe upscaled only up to 1080i.· When the “Resolution” is set to “Auto”, “Frame Rate” and “Aspect Ratio”will not be available as options.OPERATIONUSING THE T 785 – SETUP MENU18ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ