NAD T 777 Owner's Manual

Also see for T 777: Quick setup guide Owner's manual Quick setup guide

NAD T 777 Owner's Manual Manual pdf 18 page image

DIGITAL AUDIOTo take advantage of the T 777’s high performance surround and digitalaudio circuitry, it is advisable that its sets of Digital Audio input are selected.There are three types of Digital Audio input for the T 777. These are HDMI,Optical and Coaxial digital input. A fourth option is “Off” whereby noincoming digital audio signal is selected by the particular Source.The desired digital audio input for a particular Source can be selected byscrolling to “Digital Audio”, press [S] and then [D/F] to step through thedesired digital input source. After finalizing the desired type of Digital Audioinput, press [S] and then [D/F] again to select the specific Digital Audioinput.The following are the sets of assignable Digital Audio input:HDMI $ HDMI 1 - 6, HDMI FrontOptical $ Optical 1 - 3Coaxial $ Coaxial 1 – 3NOTEAn incoming digital signal present at the assigned digital input willalways take precedence over the assigned analog audio input, even ifboth are present. To maintain the analog audio input for the particularSource, select “Off” at the “Digital Audio” setting of the same “Source”menu.VIDEOThere are four types of video input a particular Source could be assigned.These are HDMI, Component, S-Video and Video input. Another option is“Off”. Select “Off” if it is intended not to assign any video input to a particularSource.Navigate through the Video input selections by pressing [S] and then[D/F] to step through the selections. The following are the sets ofassignable Video input.HDMI $ HDMI 1 - 6, HDMI FrontComponent Video $ Component 1 - 3S-Video $ S-Video 1 - 3, S-Video FrontVideo $ Video 1 - 3, Video FrontIMPORTANT NOTE ABOUT THE VIDEO PERFORMANCE OF T 777The T 777 utilizes an NAD-engineered field-programmable gate array(FPGA) that is capable of enabling the conversion of analog video todigital video. This allows a single cable connection to your TV for allsources while maintaining the source’s native resolution. Interlacedvideo is converted to progressive scan over HDMI allowing completecompatibility with latest HD TVs.The T 777 also supports HDMI features that include compatibility with abroad range of 3D and HD digital video sources and displays.A/V PRESETA particular Source can be assigned a stored Preset. The parameters set upin the selected Preset number will be adopted into the particular Source itis assigned (Please refer to the separate section on “A/V Presets” for furtherunderstanding of Preset settings).Scrolling to “A/V Preset” and by pressing [S] and then [D/F], a Source couldbe assigned a Preset number ranging from Preset 1 to 5.If it is desired not to assign the particular Source a Preset setting, select“None”.TRIGGER OUTTrigger Out feature for a particular Source is dependent upon theconfigurations done in a separate menu on Trigger Setup (See “TriggerSetup” below). If “Source Setup” is assigned to all three Trigger output(Trigger Out 1-3) in the separate “Trigger Setup” menu window, a particularSource can have the following Trigger Out combinationsTrigger Out: 1 $ 2 $ 1 + 2 $ 3 $ 1 + 3 $ 2 + 3 $ 1+2+ 3These combinations are dependent upon the assignment of “Source Setup”for Trigger 1 Out, Trigger 2 Out or Trigger 3 Out at the “Trigger Setup” menu.Another option is “None” whereby the particular Source is not assigned anyTrigger Out.For “Trigger Out” to become enabled and assignable at “Source Setup(Normal View)” menu, make sure to carry out or note the followingbeforehand% In the separate “Trigger Setup” menu, assign Trigger 1 Out, Trigger 2 Outor Trigger 3 Out to “Source Setup.”% “Trigger Out” will not appear as an option at the Source Setup (NormalView) menu if at the separate “Trigger Setup” menu, Trigger 1 Out,Trigger 2 Out or Trigger 3 Out are all assigned to “Main, Zone 2, Zone 3,Zone 4, or Zone 2+3+4”; with not even one “Trigger Out” port allocatedto “Source Setup.”SOURCE SETUP (TABLE VIEW)The Source Setup (Table View) reflects the settings made in the SourceSetup (Normal View) menu. All the Source settings are summarized anddisplayed in tabulated form in the Source Setup (Table View).Navigating through the Source Setup (Table View) via a combinationof [A/S] and then [D/F] buttons, one will have the benefit of directlychanging the settings for “Audio”, “Video”, “Preset” and “Name” withoutgoing back to the Source Setup (Normal View) menu.Highlight a particular Source number and then, toggle [ENTER] buttonto enable or disable said Source number.OPERATIONUSING THE T 777 – SETUP MENU18ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ