Mitsubishi Electric ERNT-ASLT62DA User Manual

Mitsubishi General-Purpose Programmable ControllerRenewal ToolConversion AdapterModelERNT-ASLT62DAUser’s Manual50CM-D180172-A(1404)HEAD OFFICE:Hulic KUDAN BLDG.1-13-5 KUDANKITA CHIYODA-KU TOKYO 102-0073 JAPANNAGOYA ENGINEERING OFFICE:139 SHIMOYASHIKICHO-SHIMOYASHIKI KASUGAI AICHI 486-0906 JAPAN SAFETY PRECAUTIONS (Always read these precautions prior to use.)Before using this product, please read this manual carefully and pay full attention to safety to ensure thatthe product is used correctly.The precautions presented in this manual are concerned with this product only. For ProgrammableController system safety precautions, refer to the user’s manual of the MELSEC-L series CPU module tobe used.In this manual, the safety precautions are ranked as “WARNING” and “CAUTION.”Indicates that incorrect handling may cause hazardous conditions,resulting in death or severe injury.WARNINGIndicates that incorrect handling may cause hazardous conditions,resulting in medium or minor injury and/or property damage.CAUTIONNote that failure to observe the CAUTION level instructions may lead to a serious consequenceaccording to the circumstances. Always follow the precautions of both levels because they are importantto personal safety.Please keep this manual in an easy-to-access location for future reference, and be sure to provide themanual to the end user.[Precautions before using]CAUTION When making a switch from the MELSEC-AnS Series to the MELSEC-L Series, be sure toconsult user's manual supplied with individual module under the MELSEC-L Series to confirmdifferences in various aspects including performance, function, CPU input/output signals andbuffer memory addresses between the two series.[Installation Precautions]CAUTION Use the Conversion Adapter in the environmental conditions that are specified in the generalspecification. If the Products are used in any environment beyond the bounds of the generalspecification, electric shock, fire, malfunction, or damage to or degradation of the Products willresult. Do not directly touch any conductive parts of Conversion Adapter. Contact will causemalfunction or failure in the system. Fasten the Conversion Adapter and the Mounting Bracket securely with retaining screws, andtighten the screws by applying torque within specified limits. Loose screws can lead to thedropping of the Conversion Adapter or Mounting Bracket, possibly causing breakage thereof.Excessive tightness of the screws can lead to breakage of the screws, Conversion Adapter,Mounting Bracket, or MELSEC-L Series Module, possibly causing the dropping, shorting, andmalfunction thereof. Always check for correct match between MELSEC-L Series and the Conversion Adapter.Incorrect match can cause damage to the MELSEC-L Series Module. When installing the Conversion Adapter, take care not to get your hand snagged on theMounting Bracket or the like. Injury may result. When installing or removing the MELSEC-L Series Module complete with a ConverterAdapter, be sure to hold it with both hands. Dropping may lead to breakage.[Wiring Precautions]WARNING Before attempting to install the Unit or carry out the necessary wiring, make certain that theexternal power supply, used in the system, is shut off on all three phases. Failure to do so mayresult in electric shock or damage to the product. After installation and wiring, close the terminal block cover before turning on the module foroperation. Failure to do so may result in electric shock.CAUTION Carry out wiring for the Conversion Adapter correctly after checking the specification andterminal arrangement for the module used. Connecting a power supply with a different voltagerating or incorrect wiring may cause a fire or failure. Tighten the MELSEC-AnS Series terminal installation screws and terminal screw securely byapplying torque within the specified limits. Loose screws will cause short circuit, fire ormalfunction. Excessive tightening will damage the screws or the Conversion Adapter which inturn will cause dropping of parts, short circuit or malfunction. Use care to prevent foreign materials including cuttings and wiring debris from entering theConversion Adapter or the MELSEC-L Series Module. These will be cause for fire, failure ormalfunction.[Startup and Maintenance Precautions]WARNING Do not touch live terminals. There is a danger of electric shock or malfunction. Shut off the external power supply for the system in all phases before cleaning orretightening the terminal screws. Failure to do so may result in electric shock or cause theMELSEC-Q Series module to fail or malfunction. Loose screws can lead to dropping,shorting, and malfunction. Excessive tightness of the screws can lead to breakage of thescrews, Conversion Adapter, Mounting Bracket, or MELSEC-Q Series Module, possiblycausing the dropping, shorting, and malfunction thereof.CAUTION Do not modify the Conversion Adapter or take it apart. Doing so will cause failure,malfunction, personal injury, or fire. Do not drop the Conversion Adapter and Mounting Bracket or do not give a strong impactto it. This will cause damage.[Disposal Precautions]CAUTION When disposing of the product, treat it as industrial waste.EMC AND LOW VOLTAGE DIRECTIVESCompliance to the EMC Directive, which is one of the EU Directives, has been a legal obligationfor the products sold in European countries since 1996 as well as the Low Voltage Directivesince 1997.Manufacturers who recognize their products are compliant to the EMC and Low VoltageDirectives are required to declare that print a "CE mark" on their products.Authorized representative in EuropeAuthorized representative in Europe is shown below.Name: Mitsubishi Electric Europe BVAddress: Gothaer strasse 8, 40880 Ratingen, Germany1 OverviewThis manual describes specifications, handling and other information about the Conversion Adapter“ERNT-ASLT62DA” available as Renewal Tools for the Mitsubishi General-Purpose ProgrammableController.The Conversion Adapter is a product for effecting conversion to transcend difference in pinassignment between the MELSEC-AnS Series and the MELSEC-L Series.Before attempting to make a switch from MELSEC-AnS Series to MELSEC-L Series in yourinstallation, consult the user's manual supplied with individual module under the latter series to learnabout how they differ in various aspects including performance and function.Once you have opened the packaging, verify that it contains the following products.Product Shape QuantityConversion Adapter 1Mounting bracket 1Mounting bracket fixing screws (M3.5 x 6) 1Terminal block cover 1This manual 12 General SpecificationsItem SpecificationsOperating ambienttemperature 0 to 55Storage ambienttemperature -25 to 75Operating ambienthumidity 5 to 95%RH non-condensingStorage ambienthumidityVibrationresistanceCompliant withJIS B 3502andIEC 61131-2Frequency ConstantaccelerationHalfamplitude Sweep countUnderintermittentvibration5 to 8.4Hz 3.5mm 10 times each inX, Y, Z directions8.4 to 150Hz 9.8m/s2Undercontinuousvibration5 to 8.4Hz 1.75mm8.4 to 150Hz 4.9m/s2Shock resistance Compliant with JIS B 3502 and IEC 61131-2(147 m/s2, 3 times each in 3 directions X, Y, Z)Operating atmosphere No corrosive gasesOperating altitude *1 0 to 2000mInstallation location Inside a control panelOvervoltage category *2 II or lessPollution degree *3 2*1 Do not use or store under pressure higher than the atmospheric pressure of altitude 0m.*2 This indicates the section of the power supply to which the equipment is assumed to be connected betweenthe public electrical power distribution network and the machinery within premises.Category II applies to equipment for which electrical power is supplied from fixed facilities.*3 This index indicates the degree to which conductive material is generated in terms of the environment inwhich the equipment is used.Pollution level 2 is when only non-conductive pollution occurs. A temporary conductivity caused bycondensing must be expected occasionally.3 Product SpecificationsFor detail specifications which do not appear in the specification comparison charts contained herein, see the user's manual supplied with the MELSEC-L Series module you use. Those parts of the specification thatdiffer between the MELSEC-AnS Series and the MELSEC-L Series are where a switch from the first series to the second is subjected to specification-related restrictions. Check the specification of the devices to beconnected for more details.Furthermore, it is recommended to refer to the “Transition from MELSEC-AnS/QnAS (Small Type) Series to L Series Handbook (Intelligent Function Modules): L (NA)-08259ENG” issued by Mitsubishi Electric.Conversion AdapterModelBefore replacementMELSEC-AnS SeriesModule ModelNo. ofchannelsAfter replacementMELSEC-L SeriesModule ModelConversionAdapterWeight (g)No. ofmodulesERNT-ASLT62DA A1S62DA 2 L60DA4 1 75Internal circuit diagram of ERNT-ASLT62DAA1S62DATerminal BlockL60DA4Terminal BlockTB2TB4TB6TB8TB10TB12TB14TB16TB18TB20TB1TB3TB5TB7TB9TB11TB13TB15TB17TB19TB2TB4TB6TB8TB10TB12TB14TB16TB18TB1TB3TB5TB7TB9TB11TB13TB15TB17TerminalNo.TB1TB2TB3TB5TB6TB7TB8TB9TB10TB11TB12TB13TB14TB15TB16TB17TB18TB19TB20TB4SignalName24GFGV+COMI+CH1CH2CH3CH4TerminalNo.TB1TB2TB3TB5TB6TB7TB8TB9TB10TB11TB12TB13TB14TB15TB16TB17TB18TB4 SLDV+COMI+SLDV+COMI+SLDV+COMI++24V13332SignalNameTESTTESTOpen(24G)Open(FG)V+V-I+I-CH1CH2V+V-I+I-Open(SLD)Open(+24V)Open(SLD)OpenOpenOpenHLD/CLRHLD/CLR< Specification Comparison >ModelSpecificationsMELSEC-AnS Series MELSEC-L SeriesA1S62DA L60DA4Digital inputVoltage1/4000 -4000 to 40001/8000 -8000 to 80001/12000 -12000 to 12000 -20480 to 20479(When using the scaling function -32768 to 32767)Current1/4000 0 to 40001/8000 0 to 80001/12000 0 to 12000Analog output Voltage -10 to 0 to 10VDC (external load resistance 2kΩ to 1MΩ) -10 to 10VDC (external load resistance 1kΩ to 1MΩ)Current 0 to 20mADC (external load resistance 0Ω to 600Ω) 0 to 20mADC (external load resistance 0Ω to 600Ω)I/O characteristicsMaximum resolutionOverall accuracy ±1.0% (Voltage output ±100mV, Current output ±200μA) Ambient temperature 25±5 Within ±0.1% (voltage ±10mV, current ±20μA)Ambient temperature 0 to 55 Within ±0.3% (voltage ±30mV, current ±60μA)Maximum conversion speed Maximum 25ms/2 channels (same for 1 channel) 20μs/channelAbsolute maximum output Voltage ±12VCurrent 28mAAnalog output points 2 channels 4 channelsInsulationmethodBetween outputterminals andprogrammablecontroller powersupplyPhotocoupler insulation Photocoupler insulationBetween terminals No insulation No insulationBetween externalpower supply andanalog outputTransformer insulationNumber of occupied I/O points 32 points 16 pointsConnected terminal block 20-point terminal block 18-point terminal blockExternalpower supplyVoltage 24VDC +20% -15%Current 0.18ACurrent consumption 0.8A 0.16A*1 When the offset value is set to 0V and the gain value is set to 10V.*2 When the offset value is set to 4mA and the gain value is set to 20mA.Make sure the section of the above table meets the specification of the machines and equipment connected to the MELSEC-L Series module.Precautions for programming(1) A1S62DA and L60DA4 differ from each other in the way input/output signals (X, Y) and buffer memory addresses are allocated. Therefore, you need make necessary changes to the sequence program that isused.(2) CH3 and CH4 of L60DA4 cannot be used.Precautions for wiringL60DA4 is not provided with a terminal for Offset/Gain setting or Output Hold/Clear settingpurposes.Make Output Hold/Clear setting by choosing an appropriate L60DA4 intelligent functionmodule switch setting.For more details about the Offset/Gain setting and Output Hold/Clear setting, see the L60DA4User’s Manual.L60DA4 requires power supply. Therefore, use the opened terminals(TB18, TB19) ofA1S62DA to provide 24VDC power supply to L60DA4.Connect the shield wires of each channel to the opened terminals (TB11 and TB17) ofA1S62DA, and make sure to ground the FG terminal (TB18) of L60DA4 by using the openedterminal (TB20) of A1S62DA.12Resolution 1/4000 1/8000 1/12000Analog outputVoltageoutput(*1)Currentoutput(*2)Digital input value4000 8000 12000 10V 20mA2000 4000 6000 5V 12mA0 0 0 0V 4mA-2000 -4000 -6000 -5V --4000 -8000 -12000 -10V -1/4000 1/8000 1/12000Voltage output 2.5mV 1.25mV 0.83mVCurrent output 5μA 2.5μA 1.7μAAnalog output range Digital value ResolutionVoltage0 to 5V 0 to 20000 250μV1 to 5V 200μV-10 to 10V -20000 to 20000 500μVUser range setting 333μVCurrent0 to 20mA 0 to 20000 1000 A4 to 20mA 800 AUser range setting -20000 to 20000 700 A3

/ 2

Related manuals for Mitsubishi Electric ERNT-ASLT62DA