Makita LS0714 Instruction Manual

Also see for LS0714: Instruction manual Instruction manual Instruction manual Parts Breakdown Instruction manual

21 ENGLISHEXAMPLE In the case of cutting 52/38° type crownmolding for position (1) in Fig. A:• Tilt and secure bevel angle setting to 33.9°LEFT.• Adjust and secure miter angle setting to 31.6°RIGHT.• Lay crown molding with its broad back (hidden)surface down on the turn base with its CEILINGCONTACT EDGE against the guide fence onthe saw.• The finished piece to be used will always beon the LEFT side of the blade after the cut hasbeen made.In the case of right bevel cutMoldingposition inFig. ABevel angle Miter angleFor outsidecornerFor insidecorner52/38° type 45° typeRight 31.6°45° typeRight 33.9° Right 30°52/38° typeLeft 31.6° Left 35.3°Right 35.3°Right 35.3°Right 31.6°(1)(2)(3)(4)Table (A)Moldingposition inFig. AMolding edge againstguide fence(1)ForoutsidecornerFor insidecornerFinished piece(2)(3)(4)Table (B)Finished piecewill be on theLeft side ofblade.Finished piecewill be on theRight side ofblade.Wall contact edge should beagainst guide fence.Wall contact edge should beagainst guide fence.Ceiling contact edge shouldbe against guide fence.EXAMPLE In the case of cutting 52/38° type crownmolding for position (1) in Fig. A:• Tilt and secure bevel angle setting to 33.9°RIGHT.• Adjust and secure miter angle setting to 31.6°RIGHT.• Lay crown molding with its broad back (hidden)surface down on the turn base with its WALLCONTACT EDGE against the guide fence onthe saw.• The finished piece to be used will always be onthe RIGHT side of the blade after the cut hasbeen made.Cutting aluminum extrusion► Fig.48: 1. Vise 2. Spacer block 3. Guide fence4. Aluminum extrusion 5. Spacer blockWhen securing aluminum extrusions, use spacer blocksor pieces of scrap as shown in the figure to preventdeformation of the aluminum. Use a cutting lubricantwhen cutting the aluminum extrusion to prevent build-upof the aluminum material on the blade.CAUTION:• Never attempt to cut thick or round aluminumextrusions. Thick aluminum extrusions maycome loose during operation and round alumi-num extrusions cannot be secured firmly withthis tool.Wood facingUse of wood facing helps to assure splinter-free cutsin workpieces. Attach a wood facing to the guide fenceusing the holes in the guide fence.See the figure concerning the dimensions for a sug-gested wood facing.1 135mm(1-3/8")100mm 70mm92mm 85mm(3-3/8")(2-3/4")(3-15/16")(3-5/8")27mm (1-1/16")(2"-2-3/8")50mm-60mmOver 420mm (16-1/2")Over 15mm (5/8")1. HolesCAUTION:• Use straight wood of even thickness as thewood facing.• Use screws to attach the wood facing to theguide fence. The screws should be installed sothat the screw heads are below the surface ofthe wood facing.• When the wood facing is attached, do not turnthe turn base with the handle lowered. Theblade and/or the wood facing will be damaged.Cutting repetitive lengthsCAUTION: For the tool equipped with the hold-ers and the holder assemblies as standard acces-sories, this type of use is not permitted due to thecountry regulations.► Fig.49: 1. Set plate 2. Holder 3. ScrewWhen cutting several pieces of stock to the samelength, ranging from 220 mm to 385 mm, use of the setplate (optional accessory) will facilitate more efficientoperation. Install the set plate on the holder (optionalaccessory) as shown in the figure.Align the cutting line on your workpiece with either theleft or right side of the groove in the kerf board, andwhile holding the workpiece from moving, move theset plate flush against the end of the workpiece. Thensecure the set plate with the screw. When the set plateis not used, loosen the screw and turn the set plate outof the way.NOTE:• Use of the holder-rod assembly (optional acces-sory) allows cutting repetitive lengths up to2,200 mm approximately.

/ 132

Related manuals for Makita LS0714

Makita LS0714 Instruction Manual

This manual is suitable for:

LS0714 LS0714FL LS0714F LS0714L

Makita LS0714 Instruction Manual

Product

Learn More

Legal