OneStart

Menu
Lenovo 46M4002 Installation And Maintenance Manual Manual pdf 58 page image

Lenovo 46M4002 Installation And Maintenance Manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 previewPage 36 previewPage 37 previewPage 38 previewPage 39 previewPage 40 previewPage 41 previewPage 42 previewPage 43 previewPage 44 previewPage 45 previewPage 46 previewPage 47 previewPage 48 previewPage 49 previewPage 50 previewPage 51 previewPage 52 previewPage 53 previewPage 54 previewPage 55 previewPage 56 previewPage 57 previewPage 58 previewPage 59 previewPage 60 previewPage 61 previewPage 62 previewPage 63 previewPage 64 previewPage 65 previewPage 66 previewPage 67 previewPage 68 previewPage 69 previewPage 70 previewPage 71 previewPage 72 previewPage 73 previewPage 74 previewPage 75 previewPage 76 previewPage 77 previewPage 78 previewPage 79 previewPage 80 previewPage 81 previewPage 82 previewPage 83 previewPage 84 previewPage 85 previewPage 86 preview
Contents
  1. Table Of Contents
  2. Chapter 1. Introduction
  3. Installation requirements
  4. Parts that come with the 1U PDU models
  5. Features of the PDU
  6. Hardware components
  7. Rear view
  8. PDU load groups
  9. Chapter 2. Installing the 1U PDU vertically in a rack cabinet
  10. Installing the PDU in the side of an Enterprise rack cabinet only
  11. Chapter 3. Installing the 1U PDU horizontally in a rack cabinet
  12. Chapter 4. Cabling the PDU
  13. Connecting to a LAN
  14. Connecting output devices
  15. status
  16. Power-on sequencing (some models)
  17. Using HyperTerminal through the serial port
  18. Using Telnet through the Ethernet port
  19. Using SNMP through the Ethernet port
  20. Using the web interface
  21. Starting the web interface
  22. Power management relay setting
  23. Modifying the basic settings
  24. Changing the network configuration
  25. Chapter 6. Using the PDU environment sensor
  26. Chapter 7. Customer replaceable unit parts
  27. Chapter 8. PDU specifications
  28. Appendix A. Default PDU settings
  29. Appendix B. Behavior of the PDU reset button
  30. Appendix C. Getting help and technical assistance
  31. Using the documentation
  32. Software service and support
  33. Appendix D. Notices
  34. Trademarks
  35. Particulate contamination
  36. Federal Communications Commission (FCC statement
  37. Japanese electromagnetic compatibility statements
  38. Korea Communications Commission (KCC statement
  39. People's Republic of China Class A electronic emission statement
Lenovo 46M4002 Installation And Maintenance Manual Manual pdf 58 page image
1. If applicable, connect external contact inputs to the screw terminals on the PDU environment sensor.PDU environment sensorscrew terminalsPin 1Note: External contact device 1 is connected between pins 1 and 2. Device 2 is connected betweenpins 3 and 4 (as labeled to show device 1 and 2). External contact devices can be normally open ornormally closed.Table 4. PDU environment sensor screw terminal pin assignmentPin number DescriptionNormally open/ normallyclosed1 Contact 1 return Normally closed2 Contact 1 signal input Normally open3 Contact 2 return Normally closed4 Contact 2 signal input Normally open2. Connect the Category 5 Ethernet cable that comes with the environment sensor to the PDU environmentsensor and to the environment sensor connector on the PDU.Note: If the cable is not long enough for your configuration, you can use a cable that is 20 m (65.6 ft) orshorter.The following illustration shows how to connect an Ethernet cable to a 1U PDU and to the PDUenvironment sensor.562134LANEthernet cableEnvironmentsensor connectorPDUPDU environmentsensor3. Make sure that the PDU has a network connection, the power cord is connected, and the power to thePDU is turned on. The PDU environment sensor is automatically recognized by the PDU.4. Start a web browser and connect to the PDU IP address (for more information, see “Using the webinterface” on page 39). The web interface main status page opens. Click Environment, and then click50 1U C19 and C13 Switched and Monitored PDUs Installation and Maintenance Guide
/ 86
Related manuals for Lenovo 46M4002
Lenovo System x PDU Technical Reference first page preview
Lenovo System x PDU Technical Reference
This manual is suitable for:
46M400246M400346M400446M4005
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved