OneStart

Menu
JVC KM-H2500E Instructions Manual Manual pdf 10 page image

JVC KM-H2500E Instructions Manual

Also see for KM-H2500: Manual User manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 previewPage 36 previewPage 37 previewPage 38 previewPage 39 previewPage 40 previewPage 41 previewPage 42 previewPage 43 previewPage 44 previewPage 45 previewPage 46 previewPage 47 previewPage 48 previewPage 49 previewPage 50 previewPage 51 previewPage 52 previewPage 53 previewPage 54 previewPage 55 previewPage 56 preview
Contents
  1. safety precautions
  2. environmental information
  3. Table Of Contents
  4. Introduction
  5. Control Panel Rear Connections Overview
  6. Knobs
  7. Shift
  8. Configuration
  9. Output Reference Sync
  10. Aspect Ratio
  11. Input BNC Configuration
  12. Clean Feed
  13. Switcher Personality
  14. Basic Operation
  15. Configuring the Auto Trans Rate
  16. Key Transitions
  17. Dedicated Key Transitions
  18. Mattes
  19. Fade to Black
  20. Advanced Operation
  21. Memory AI and Recall to Preview
  22. Transition Limit
  23. Reset Options
  24. USB Storage
  25. Software Upgrades
  26. Advanced Keying
  27. Modifying Wipes
  28. Tallies
  29. General Purpose Interface (GPI)
  30. Media-Store
  31. Understanding Media Numbers
  32. Modifying Media-Store Image Attributes
  33. Animation Control
  34. Specifications
  35. Error Messages
JVC KM-H2500E Instructions Manual Manual pdf 10 page image
42. Remove the Lens (1) from the Diffuser (2) usinga common end micro screwdriver.3. Place the Insert Film (2) into the Lens (1) so thereadable side is facing up. The notches on thesides of the Lens must be at the sides of the texton the Insert Film.4. Aligning the notches on the sides of the Lens (1)and Diffuser (3), press the Lens and Diffusertogether until they click.5. Aligning the notches on the sides of the CapAssembly (1) to the tabs on the side of theSwitch Assembly (2), press Cap Assembly downonto the Switch Assembly with a rolling motionuntil they click together.ShiftShifting allows access to the secondary sources foreach source button.To shift a bus and access the secondary sources:1. Press and hold SHIFT.2. Press the required source button to access thesecondary source.FaderThe Fader is used to manually perform a wipe ordissolve transition. Move the Fader handle from onelimit to the other to perform a transition.TransitionsThe progress of the transition is shown on theProgress Bar to the left of the Fader handle. As theFader handle moves from one limit to the other, theProgress Bar indicates the progress of the transition.PositionerThe KM-H3000 has a joystick positioner forpositioning wipes, patterns, and washes. TheKM-H2500 does not have a positioner.Selecting ColorsFunctions such as mattes, and Panel Glow haveoptions for adjusting the appearance of a selectedcolor. Individual adjustments for colors are:• Luminance• Hue• SaturationLuminanceLuminance affects the brightness of the video signal.Increasing luminance gives a brighter color whiledecreasing luminance gives a darker color.HueHue controls the shade of color (red, yellow, green,blue, etc.).SaturationSaturation affects the vividness of a color. Increasingsaturation produces a more vivid color whiledecreasing saturation produces a less vivid color.Fully decreasing the saturation produces gray.21CUT2312112
/ 56
This manual is suitable for:
KM-H2500KM-H2500EKM-H2500UKM-H3000EKM-H3000U
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved