JVC KA-MR100G Instructions Manual

Also see for KA-MR100G: Service manual

Contents

15OthersTroubleshootingSymptom Cause(s) Actions Refer toPower does not turnonPower is supplied from the DC INPUTterminal of the camcorder.Attach the battery. The power of the memory recordercannot be supplied from the DC INPUT terminal of thecamcorder.A Page 7Only the power of the camcorder is turnedAOnB.It is necessary to turn on the power of the memory recorderat the same time.A Page 7Remaining battery level is insufficient. Charge the battery. A Page 14Unable to record orplay clipThe IEEE1394 cable is not connected. Connect a GY-HD200/HD250 series camcorder to theKA-UM100G adapter using an IEEE1394 cable.A Page 7The [INT/EXT] switch setting of theKA-UM100G adapter is inappropriate.● Set to AEXTB during normal use. (When IEEE1394connection is made internally without the use of anexternal cable, set to AINTB.● If the ANO SIGNALB message does not disappear evenif the setting is correct, set the switch again to select thesetting. If the message remains displayed, turn off andon the power again.A Page 7The video formats of the camcorder andmemory recorder are not consistent witheach other.Ensure that the video format of the camcorder and memoryrecorder are consistent with each other.A Page 9The [IEEE1394] switch of the camcorder isset to the ADVB end.Set the [IEEE1394] switch to the AHDVB end.If the ANO SIGNALB message does not disappear evenafter setting to AHDVB, set the switch again. If the messageremains displayed, turn off and on the power again.A Page 9A Page 10Recording does notstartThe camcorder is set to the AVTRB mode. Set to the ACAMB mode using the [CAM/VTR] button. A Page 9The [1394 REC TRIGGER] item on theOTHERS[2/2] menu screen of thecamcorder is set to AOFFB or ASERIESB.Set [1394 REC TRIGGER] to ASYNCROB or ASPLITB.When this is set to ASERIESB, recording starts when theremaining capacity of the cassette tape falls below threeminutes.A Page 9The memory recorder is set to the playbackmode.Press the [STOP] button to stop playback. A Page 9The write-protect of the SxS memory cardis enabled.Set the write-protect switch to AOffB before recording ordeleting a clip.A Page 14There is no space left on the SxS memorycard.Use an SxS memory card that has sufficient space. A Page 14Unable to play clip The camcorder is set to the ACAMB mode. Set to the AVTRB mode using the [CAM/VTR] button. A Page 10The cassette tape is currently being playedback.Stop playback of the cassette tape before playing backdata on the SxS memory card.A Page 10A clip without the check mark (v) isselected.Set the camcorder and memory recorder according to thevideo format displayed when a clip is selected.A Page 10The memory recorder is in the recording orstandby mode.Press the [STOP] button to stop playback. A Page 10The clip may be damaged. Execute ARESTOREB using this memory recorder. A Page 14No response when abutton is pressedThe [OPERATION] menu is set to ALOCKB. Change the [OPERATION] menu setting to AUNLOCKB. A Page 14A multiple number of buttons are pressedat the same time, or the same button is hitrepeatedly.Insert a short pause between each button operation.^Access lamp does notturn onThe SxS memory card is not completelyinserted into the card slot.Make sure that the SxS memory card is fully inserted intothe slot.A Page 8The SxS memory card is inserted with thelabel facing the opposite direction.Identify the face of the SxS memory card with the label,and make sure that the card is correctly oriented beforeinserting.A Page 8SxS memory cardcannot be usedA SxS memory card that is formatted byanother device is used.Execute AFORMATB using this memory recorder. A Page 13A media that is not supported is inserted. Replace it with a recommended SxS memory card. A Page 14The clip is faulty. Execute ARESTOREB or AFORMATB using this memoryrecorder. If doing so does not eliminate the error, replace itwith a recommended SxS memory card.A Page 14Error messageappears on thecamcorder paneldisplayADR-HD100 POWER ?B appears when thememory recorder is not powered on or isnot connected.Connect and turn on the power of the memory recorder. A Page 6A Page 7AHDD NO 1394 SIGNALB appears if thecamcorder is set to the “CAM” mode whenthe memory recorder is in playback mode.Set the camcorder to the AVTRB mode. A Page 10AHDD SPACE LOWB appears when thespace on the SxS memory card isinsufficient or an SxS memory card is notinserted.Use an SxS memory card that has sufficient space.^

/ 20

Related manuals for JVC KA-MR100G