Contents - Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Section 1: Quick Setup
- Section 2: System Operation
- Direct Access
- Exiting from Engineer Mode
- Multi User Access
- Section 3: Setting Options
- Unsetting the System
- Card Setting Options
- Setting Features
- Omitted Zones
- Abort Time
- Section 4: Menu Options 11-19
- Option 12 – Timed Set
- Option 17 – Instant Part
- Section 5: Display Options
- Option 22 – Display Log (Quick Menu Option 4)
- Option 23 – System (Galaxy 18, 60, 128, 500, 504 & 512)
- Option 24 – Print (Quick Menu Option 5)
- Option 25 – Access Doors
- Section 6: Test Options
- Option 32 – Outputs
- Section 7: Modify Options
- Option 42 – Codes (Quick Menu Option 8)
- Default Codes
- Escaping from Engineer Mode
- Programming Codes
- Option 43 – Summer (Quick Menu Option 9)
- Option 45 – Timer Control (Galaxy 18, 60, 128, 500, 504 & 512)
- Option 46 – Group Omit (Galaxy 18, 60, 128, 500 & 504)
- Option 47 – Remote Access
- Option 48 – Engineer Access (Galaxy 512 only)
- Option 49 – Datelock (Galaxy 512)
- Section 8: Engineer 1
- Option 52 – Program Zones
- System Alarms
- Option 53 – Program Outputs
- Attributes
- Output Functions
- Option 54 – Links (Galaxy 18, 60, 128, 500, 504 & 512)
- Option 55 – Soak
- Option 56 – Communications
- Telecom Module
- RS232 Interface Module
- ISDN Module
- Ethernet Module
- Option 57 – System Print
- Option 58 – Keypad
- Option 59 – Quick Menu
- Section 9: Engineer 2
- Option 62 – Full Test (Galaxy 18, 60, 128, 500, 504 & 512)
- Option 63 – Options (Galaxy 18, 60, 128, 500, 504 & 512)
- Option 64 – Assemble Zone (Galaxy 18, 60, 128, 500, 504 & 512)
- Option 65 – Timers (Galaxy 18, 60, 128, 500, 504 & 512)
- Option 66 – Pre-checks (Galaxy 60, 128, 500, 504 & 512)
- Option 67 – Remote Reset
- Option 68 – Menu Access (Galaxy 60, 128, 500, 504 & 512)
- Appendix A : Door Control - MAX (MX01)
- Mounting the MAX
- Configuring a MAX Reader into the System
- Configuring as On-Line MAX
- Removing a MAX Reader from the System
- Operating Instructions (On-Line Modes)
- Max Events Print-Out
- Appendix B: Library
- Appendix C: SIA and Contact ID Event Codes
- Appendix D: SIA Event Structure
- Appendix E: Event Log Messages
|
Galaxy Programming Manual431 = Weekend DayOn selecting this option the programmed Weekend Day is displayed; the default is 0 = OFF. Use the A or Bkeys to select the required day or days and press the ent key to accept the programming and return to theprevious menu level:0 = OFF1 = SAT2 = SUN3 = BOTH (Saturday and Sunday)The selected Weekend Day remains active for one occurrence only. The Weekend Day returns to thedefault of OFF immediately following the assigned day. The Weekend Day must be allocated each time thefunction is required.2 = Pattern DayThe Pattern Day can only be allocated by the engineer. This option determines the programmed timers thatare effective when the Weekend Day option is selected by the user; the timers of the selected Pattern Dayare adopted by the days selected for weekend work.On selecting this option the programmed Pattern Day is displayed; the default is 1 = MON. Use the A or Bkeys to select the required day or days and press the ent key to accept the programming and return to theprevious menu level:1 = MON2 = TUE3 = WED4 = THU5 = FRI45 - Timer Control (cont’d)
|
