Contents - Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Section 1: Quick Setup
- Section 2: System Operation
- Direct Access
- Exiting from Engineer Mode
- Multi User Access
- Section 3: Setting Options
- Unsetting the System
- Card Setting Options
- Setting Features
- Omitted Zones
- Abort Time
- Section 4: Menu Options 11-19
- Option 12 – Timed Set
- Option 17 – Instant Part
- Section 5: Display Options
- Option 22 – Display Log (Quick Menu Option 4)
- Option 23 – System (Galaxy 18, 60, 128, 500, 504 & 512)
- Option 24 – Print (Quick Menu Option 5)
- Option 25 – Access Doors
- Section 6: Test Options
- Option 32 – Outputs
- Section 7: Modify Options
- Option 42 – Codes (Quick Menu Option 8)
- Default Codes
- Escaping from Engineer Mode
- Programming Codes
- Option 43 – Summer (Quick Menu Option 9)
- Option 45 – Timer Control (Galaxy 18, 60, 128, 500, 504 & 512)
- Option 46 – Group Omit (Galaxy 18, 60, 128, 500 & 504)
- Option 47 – Remote Access
- Option 48 – Engineer Access (Galaxy 512 only)
- Option 49 – Datelock (Galaxy 512)
- Section 8: Engineer 1
- Option 52 – Program Zones
- System Alarms
- Option 53 – Program Outputs
- Attributes
- Output Functions
- Option 54 – Links (Galaxy 18, 60, 128, 500, 504 & 512)
- Option 55 – Soak
- Option 56 – Communications
- Telecom Module
- RS232 Interface Module
- ISDN Module
- Ethernet Module
- Option 57 – System Print
- Option 58 – Keypad
- Option 59 – Quick Menu
- Section 9: Engineer 2
- Option 62 – Full Test (Galaxy 18, 60, 128, 500, 504 & 512)
- Option 63 – Options (Galaxy 18, 60, 128, 500, 504 & 512)
- Option 64 – Assemble Zone (Galaxy 18, 60, 128, 500, 504 & 512)
- Option 65 – Timers (Galaxy 18, 60, 128, 500, 504 & 512)
- Option 66 – Pre-checks (Galaxy 60, 128, 500, 504 & 512)
- Option 67 – Remote Reset
- Option 68 – Menu Access (Galaxy 60, 128, 500, 504 & 512)
- Appendix A : Door Control - MAX (MX01)
- Mounting the MAX
- Configuring a MAX Reader into the System
- Configuring as On-Line MAX
- Removing a MAX Reader from the System
- Operating Instructions (On-Line Modes)
- Max Events Print-Out
- Appendix B: Library
- Appendix C: SIA and Contact ID Event Codes
- Appendix D: SIA Event Structure
- Appendix E: Event Log Messages
|
Galaxy Programming Manual11215 PriorityNot used16 Force V.21This is used to change the modem speed to 300 baud. This option may require to be selected when using theTelecom module on PSTN lines shared with RedCARE devices.17 SMSThe SMS option is available on Galaxy panels with V4.00 and above software and Telecom modules withV5.xx and above software. This option generates and transmitts SMS text messages, for events generated bythe Galaxy panel.1=Mobile No.This is a 22 digit telephone number and is the mobile phone number of the recipient of the message.2=Centre No.This is a 22 digit telephone number and is the phone number of the SMS centre. The default is different foreach operator.3=FormatThe options for this menu are:1=TAPFor mobile phones (UK)2=UCP (SMS)For mobile phones (outside UK)3=UCP (Minicall)For alpha pagers4=UCP (Numeric)For numeric pagers4=Site IDThis is a 16 character alphanumeric string and is used to identify the panel/site sending the message. If theformat is UCP (Numeric), then the site ID is numeric only, and only the first four characters are sent out.5=PasswordThis is a 16 character string and is an optional field required by some paging centres.56 - Communications (cont’d)
|
