Honeywell ADEMCO VISTA SERIES Programming Manual

Also see for ADEMCO VISTA SERIES: Installation and operation guide Programming guide Installation and setup guide Quick guide Faq

Contents

Honeywell ADEMCO VISTA SERIES Programming Manual Manual pdf 42 page image

FCC STATEMENTSFEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual.Unauthorized changes or modifications could void the user's authority to operate the equipment.CLASS B DIGITAL DEVICE STATEMENTThis equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement foryour information:This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with themanufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with thelimits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to providereasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur ina particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• If using an indoor antenna, have a quality outdoor antenna installed.• Reorient the receiving antenna until interference is reduced or eliminated.• Move the radio or television receiver away from the receiver/control.• Move the antenna leads away from any wire runs to the receiver/control.• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.• Consult the dealer or an experienced radio/TV technician for help.This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.FCC/IC STATEMENTThis device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that maycause undesired operation.Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis auxconditions suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reçue ycompris les interferences causant une reception indésirable.TELEPHONE/MODEM INTERFACEFCC Part 68This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains the FCC registrationnumber and Ringer Equivalence Number (REN). You must provide this information to the telephone company when requested.This equipment uses the following USOC jack: RJ31XThis equipment may not be used on telephone-company-provided coin service. Connection to party lines is subject to state tariffs. Thisequipment is hearing-aid compatible.Industry CanadaNOTICE: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets telecommunicationsnetwork protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirementsdocument(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunicationscompany. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliancewith the above conditions may not prevent degradation of service in some situations.Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by theuser to this equipment, or equipment malfunctions, may give the telecommunications company to request the user to disconnect theequipment.Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallicwater pipe system, if present, are connected together, This precaution may be particularly important in rural areas.Caution: Users should not attempt to make such connections themselves but should contact appropriate electric inspection authority, orelectrician, as appropriate.Ringer Equivalence Number Notice:The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminalsallowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only tothe requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.Industrie CanadaAVIS: l’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes deprotection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigencestechniques relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’enterprise locale detélécommunication. Le matériel doit également être installé en suivant une méthode acceptée da raccordement. L’abonné ne doit pas oublierqu’il est possible que la conformité aux conditions énoncées ci-dessus n’empêche pas la dégradation du service dans certaines situations.Les réparations de matériel nomologué doivent être coordonnées par un représentant désigné par le fournisseur. L’entreprise detélécommunications peut demander à l’utilisateur da débrancher un appareil à la suite de réparations ou de modifications effectuées parl’utilisateur ou à cause de mauvais fonctionnement.Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source d’energie électrique, de lignestéléphoniques et des canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importantedans les régions rurales.Avertissement : L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir racours à un service d’inspection desinstallations électriques, ou à un électricien, selon le cas.AVIS : L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux quipeuvent être raccordés à une interface. La terminaison d’une interface téléphonique peut consister en une combinaison de quelquesdispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.– 42 –