OneStart

Menu

Hach SD900 User Manual

Also see for SD900: Basic user manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Page 41 preview
Page 42 preview
Page 43 preview
Page 44 preview
Page 45 preview
Page 46 preview
Page 47 preview
Page 48 preview
Page 49 preview
Page 50 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. Specifications
  4. General information
  5. Safety information
  6. Product overview
  7. Product components
  8. Installation
  9. Install the sampler in a manhole
  10. Install multiple bottles
  11. Plumb the sampler
  12. Electrical installation
  13. Connect a flow meter
  14. Connect an SDI-12 device
  15. Calculate the pump cycle time
  16. Close the cover
  17. Operation
  18. Configure the SDI-12 device
  19. Set up a sampling program
  20. Time based collection
  21. Use 4–20 mA input for the flow source
  22. Constant Time Variable Volume (CTVV) sampling
  23. Start or stop a program
  24. Move the distributor arm
  25. View the event log
  26. Volume calibration
  27. Calibrate the sample volume manually
  28. Activate the full bottle shutoff
  29. Full bottle shutoff and timed bottle mode
  30. Send output signal with sample cycle (special output)
  31. Set multiple start and stop times
  32. Collect first flush stormwater samples
  33. Timed bottle sets
  34. Clean the instrument
  35. Pump maintenance
  36. Clean the rotor
  37. Replace the distributor arm tube
  38. Error messages
  39. Diagnostic tests
  40. replacement parts
Hach SD900 User Manual Manual pdf 4 page image
Start or stop a program .............................................................................................. 24View the program status ............................................................................................ 24Manual operation ....................................................................................................... 24Collect a grab sample ......................................................................................... 24Move the distributor arm ..................................................................................... 25Start or stop the pump ........................................................................................ 25View data ................................................................................................................... 25View the sample history ...................................................................................... 25View the event log .............................................................................................. 26Event log information ................................................................................... 26Erase the event log ..................................................................................... 26View data from SDI-12 devices .......................................................................... 26Volume calibration ..................................................................................................... 27Calibrate the liquid sensor .................................................................................. 27Restore the default calibration ............................................................................ 27Calibrate the sample volume with the liquid sensor ........................................... 27Calibrate the sample volume manually ............................................................... 28Verify the sample volume ................................................................................... 28Full bottle shutoff ....................................................................................................... 28Activate the full bottle shutoff .............................................................................. 29Enable the full bottle shutoff ............................................................................... 29Full bottle shutoff in non-continuous mode ......................................................... 29Full bottle shut off in continuous mode ............................................................... 29Full bottle shutoff and timed bottle mode .................................................... 30Full bottle shutoff exception conditions ............................................................... 30Advanced sampling................................................................................................ 30Send output signal at program completion ................................................................ 30Send output signal with sample cycle (special output) .............................................. 31Operate from an external signal (setpoint sample) .................................................... 31Use an SDI-12 device for setpoint sampling ..................................................... 31Set multiple start and stop times ................................................................................ 32Collect first flush stormwater samples ....................................................................... 33Set variable intervals ................................................................................................. 33Timed bottle sets ....................................................................................................... 34Maintenance............................................................................................................... 34Clean the instrument .................................................................................................. 35Replace the desiccant ............................................................................................... 35Pump maintenance .................................................................................................... 36Replace the pump tubing .................................................................................... 36Clean the rotor .................................................................................................... 38Replace the distributor arm tube ................................................................................ 39Fuse replacement ...................................................................................................... 39Troubleshooting....................................................................................................... 39General troubleshooting ............................................................................................ 39Error messages ......................................................................................................... 40Diagnostic tests ......................................................................................................... 42Replacement parts and accessories............................................................... 42Table of Contents2
/ 50
Related manuals for Hach SD900
Hach MP-Dock User Manual first page preview
Hach MP-Dock User Manual
Hach AquaTrend 51200 Instrument Manual first page preview
Hach AquaTrend 51200 Instrument Manual
This manual is suitable for:
SD900
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved