OneStart

Menu

HAMPTON BAY H200 Owners & Installation Manual

Also see for H200: Brochure & specsOwners & installation manualOwners & installation manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Contents
  1. Table Of Contents
  2. Safety Label for H200
  3. Unit Dimensions
  4. Pre-installation Assembly
  5. Residential Installation
  6. Minimum Clearance To Combustible Materials
  7. Minimum Alcove Clearance To Combustible Materials
  8. Floor Protection
  9. Step-by-step Chimney and Connector Installation
  10. Masonry Chimney
  11. Combustible Wall Chimney Connector Pass-throughs
  12. Recommended Heights For Woodstove Flue
  13. Mobile Home Installation
  14. Listed Components For Mobile Home Installation
  15. Brick Installation
  16. Optional Blower/Fan Installation
  17. Optional Side Shelf Installation
  18. Operating Instructions
  19. Safety Guidelines And Warnings
  20. Ash Drawer Kit Installation
  21. Ash Disposal
  22. Maintenance
  23. Front Door Gasket
  24. Main Assembly
  25. Door Assembly
  26. Ash Drawer Assembly
  27. Fan Assembly
  28. Warranty
HAMPTON BAY H200 Owners & Installation Manual Manual pdf 18 page image
Hampton H200 Cast Freestanding Woodstove18CAUTION: Label all wiresprior to disconnectionwhen servicing controls.Wiring errors can causeimproper and dangerousoperation.WARNING: Electrical GroundingInstructionsThis appliance is equipped witha three pronged (grounding) plugfor your protection against shockhazard and should be pluggeddirectly into a properly groundedthree-prong receptacle. Do not cutor remove the grounding prongfrom this plug.An optional blower is available for the HamptonH200. The blower is factory assembled, wiredand ready for attachment to the stove.This unit must be connected to a grounded,standard 120 volts, 60 Hz electrical outlet.Never route the power cord under or in frontof the unit.Do not under any circumstances, cut or removethe grounding prong from the power cord. Donot use an adaptor plug.CAUTION: Moving parts may cause injury.Do not operate unit with blower housingremoved.DANGER: Risk of electric shock. Discon-nect power before servicing unit.NOTE: For more detailed information seeinstructions included with the OptionalBlower.OPTIONAL BLOWER/FAN INSTALLATIONGroundFan FanGround GreenNeutralLiveWhiteFanSwitchManual/AutoSwitchBlack BlackHigh (Black)Low (Red)BlackFan Thermodisc(normally open)120V AC60 HzBlower/Fan Wiring DiagramNOTE INPUT POWER: Australia, New Zealand,China and Japan use 240V AC 50 Hz.INSTALLATION1) Remove fan cover plate from back shieldby undoing 3 screws and discard plate.2) Remove back shield by undoing 2 bolts.3) Loosen the 2 bolts you see after remov-ing back shield, one on each side of thestove.4) Hook fan over the bolts.Fan5) Tighten bolts to secure fan.Tightenbolts6) Re-install back shield.BackShield7) Using the 3 screws from the fan coverplate, secure the fan assembly to the backshield.8) Plug in power cord.
/ 32
Related manuals for HAMPTON BAY H200
HAMPTON BAY H200 Owners & Installation Manual first page preview
HAMPTON BAY H200 Owners & Installation Manual
HAMPTON BAY H300 Owners & Installation Manual first page preview
HAMPTON BAY H300 Owners & Installation Manual
HAMPTON BAY H300 Owners & Installation Manual first page preview
HAMPTON BAY H300 Owners & Installation Manual
HAMPTON BAY HI300 Owners & Installation Manual first page preview
HAMPTON BAY HI300 Owners & Installation Manual
This manual is suitable for:
H200
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved