OneStart
Menu
Home
Features
Browser
Content
Partner
Coupons
Manuals
Blog
Download
Search
Manuals database
Brands
GE
Accessories
Giraffe
GE Giraffe Service Manual
GE Giraffe Service Manual
Also see for Giraffe:
Service manual
Operation and maintenance manual
Table of content
Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
important safety information
Chapter 1: Functional Description
Figure 1-1 Block Diagram
Relay Board
Display Driver Board / EL Display
LED Board
DataLink Option
Servo Controlled Oxygen Option
Humidifier
Chapter 2: Service Checkout
Controller Checks
Humidity Check
Servo Controlled Oxygen Check
Supply Valve Leak Test
Scale Check
Off Center Weight Check
Cable Connections and Mechanical Controls
Service Maintenance Schedule
Figure 3-1 Control Board Test Points
Special Tools
Line Voltage Calibration
Servo Controlled Oxygen Calibration
Scale Calibration
Leakage Current
Startup Sequence
Service Screen
Figure 4-2 Second Service Screen
Figure 4-4 Switch Diagnostic Diagram
Figure 4-5 First Service Screen: Diagnostics
Alarm Messages
Baby Hot" or "Baby Cold" Alarm
Bed Heater Failure" Alarm
Bed Up/Down Pedal Switches Disabled" Alarm
Humidifier Failure" Alarm
Motor Drive Failure" Alarm
Up Pedal Pressed" Alarm
System Failure 1
System Failure 5
System Failure 11
System Failure 15
System Failure 16
System Failure 19
System Failure 23
System Failure 26
System Failure 30
System Failure 35
System Failure 55
Additional Troubleshooting Tips
Power Supplies
Humidifier Heater/Safety Thermostat
Incubator Heat Sink Sensor Thermistor
Troubleshooting the Toroidal Transformer
Servo Controlled Oxygen
Servo Controlled Oxygen Alarm Messages
Servo Controlled Oxygen Troubleshooting Tips
Sensor Housing Temperature Sensor Temperature to Resistance Curve
Chapter 5: Repair Procedures
Hood Removal for Replacement
Porthole Door Replacement
Uprights and End Caps
Re-installing the Upright
Compartment Probe Repairs
Lower Unit Repairs
Incubator Fan/Motor/Optical Sensor
Incubator Heater Replacement
To Remove the Heater Closest to the Head of the Bed
Elevating Base
Figure 5-8 Elevating Base with Two-piece Shroud Assembly
Figure 5-9 Elevating Base with Three-piece Shroud Assembly
Chassis Replacement
Humidifier Assembly Repairs
Humidifier Disassembly
Humidifier Reassembly
Bed Tilt Brake Pad Replacement
Caster Replacement
Controller and Display Module Procedures
Probe Panel
Battery
Controller Components
Control Board
Toroidal Transformer
Servo Controlled Oxygen Service Procedures
Replacing the Vent Screen
Calibration Valve
Valve Housing Repairs
Supply Valves
Exploded Views
Probe Housing, Display Module, and Electrical Enclosure
Figure 6-1 Probe Panel Assembly
Figure 6-2 Display Module
Figure 6-3 Electrical Enclosure
Figure 6-4 Humidifier Transformer and RS232 Option
Bed and Side Doors
Figure 6-5 Bed
Figure 6-6 Side Door (East/West)
Figure 6-7 Flip Door, Corner Brackets, and Grommets
Hood and Compartment Air Probe
Figure 6-8 Compartment Air Probe
Chassis
Figure 6-9 Upper Chassis and Heat Sink
Figure 6-10 Lower Chassis
Figure 6-11 Humidifier Assembly
Elevating Base, Old Designs
Figure 6-12 Base and Elevating Column with Two-piece Shroud Assembly
Elevating Base, Current Design
Figure 6-13 Base and Elevating Column with Three-piece Shroud Assembly
Hood Latch, Wire Covers, and Uprights
Figure 6-14 Hood Latch and Wire Covers
Figure 6-15 Uprights and End Caps
Servo Control Oxygen
Figure 6-16 Servo Control Oxygen Sensor Housing Assembly
Figure 6-17 Servo Control Oxygen Valve Housing
Figure 6-18 Expansion Chamber/Heatsink Vent
Figure 6-19 Servo Control Oxygen Cooling Fan
Figure 6-20 Servo Control Oxygen PC Board
Accessory Hangers
Storage Drawer
Figure 6-23 Storage Drawer (on Units with Three-piece Shroud Assembly)
Accessories
Labels
PCB Layouts
Figure 6-34 Relay Board (6600-0214-850) Revision Level 10 or Higher
Figure 6-35 Relay Board (6600-0214-850) Revision Level 9 or Lower
Wiring Diagrams
Figure 6-37 Wiring Diagram: Elevating Base
Figure 6-38 Wiring Diagram: Electrical Enclosure
Figure 6-39 Wiring Diagram: Graphics Display
Figure 6-40 Wiring Diagram: Incubator Heater, Relay Board Rev. Level 10 or Higher
Figure 6-41 Wiring Diagram: Incubator Heater, Relay Board Rev. Level 9 or Lower
Figure 6-42 Wiring Diagram: Incubator Fan and Sensor
Figure 6-43 Wiring Diagram: Servo Humidifier, Relay Board Rev. Level 10 or Higher
Figure 6-44 Wiring Diagram: Servo Humidifier, Relay Board Rev. Level 9 or Lower
Figure 6-45 Wiring Diagram: Servo Control Oxygen
Appendix B: Specifications
B.4 Operating Environment
B.8 Performance
B.9 Weight Scale
Appendix C: RS-232 Serial Data
C.3 Nurse Call
Appendix D: Additional Safety Information
1.9
Humidifier
Refer to the following diagram. Water enters the insulating cylinder (1) through a small hole in bottom. Steam
rises along the heater cartridge protective insert (2) and is channeled between the heater mount (3) and the
ramp block (4) and out the steam port (5).
3
4
2
1
5
Figure 1-2
Humidifier
8
6600-0356-000 103
© 2001 by Datex-Ohmeda, Inc.. All rights reserved.
Chapter 1: Functional Description
Previous
Next
/ 206
Related manuals for GE Giraffe
GE 32563 Manual
GE 19211 Manual
GE 19298 User Manual
GE 45130 User Manual
GE ZW6305 Manual
GE DPS 5000 Series User Manual
GE IMRSEN-W12 Manual
GE PowerBank M540 Manual
GE 60 Series Installation Instructions Manual
GE JASCO 32563 Quick Start Manual
This manual is suitable for:
Giraffe