FAAC E024S User Manual

Also see for E024S: Manual Manual

Contents

FAAC E024S User Manual Manual pdf 9 page image

E024S 9 732642 - Rev. FDescriptionPressingSW2(Speed)LD7 LEDstatus(Logic)LD8 LEDflashing(Speed)1Windprooffunction(anti-crushingsensitivity)OnceEnabled ON(low obstacle sensitivity)Disabled OFF(high obstacle sensitivity)1 flash2 Reversing stroke twice Enabled ONDisabled OFFFlashingtwice3 Soft-Touch 3 times Enabled ONDisabled OFFFlashing3 times4 Pre-flashing 4 times Enabled ONDisabled OFFFlashing4 times5 Leaf openingdelay 5 times Enabled ON ( 2 sec.)Disabled OFFFlashing5 times6Leaf closingdelay*( Default 5 s)6 times ON (SW3 pressing)OFF (no pressure) Flashing6 times7 Pause time*(Default 30 s) 7 times ON (SW3 pressing)OFF (no pressure)Flashing7 times8Stop point searchspace(function only active ifSAFECODER available)8 times HIGH (Short leaf) OFFLOW (Long leaf) ONFlashing8 times6.3.3 PROGRAMMING THE LOGICRepeatedly press the SW3 push-button to select one of the 7programming logics available.The selected logic is signaled by the LD7 LED.The number of flashings corresponds to the number of the selectedlogic:(default settings in bold)3. From now on, until next open impulse, the pause time iscounted.4. Open impulse ---> Pause time acquisition and start of leaf2 closing movement.5. Open impulse ---> leaf 2 decelerated closure and start ofthe search for leaf 2 closing limit stop.- if the limit stop is detected, it is set as leaf 2 stop point andleaf 1 starts to close.(*) if an open command is detected, it is set as leaf 2 stoppoint and leaf 1 starts to close.6. Open impulse --->leaf 1 decelerated closure and start ofthe search for leaf 1 closing limit stop.- if the limit stop is detected, it is set as leaf 1 closing stoppoint.(*) if an open command is detected, it is set as leaf 1 closingstop point.If the SETUP procedure is performed correctly, the LD4 andLD5 LEDs turn off at the end. Otherwise the procedure ends byasking a new SETUP with flashing LEDs.To eliminate decelerated opening and closing, send2 consecutive open impulses to determine the openingand closing stop point, otherwise have the leaf findthe opening and closing limit stop if you want to usethe limit stop facility.With the MANUAL SETUP the decelerated spaces,the leaf closing delay and the pause time aremanually set on the board during setup. Youcan modify them without repeating the setupprocedure by using the 2nd level programming.Logic Description SW3 pressing(LOGIC) LD7 flashingA Logic A (Automatic) once Flashing onceE Semi-automatic twice Flashing twiceAP Step-by-stepautomatic 3 times Flashing 3 timesEP Step-by-stepsemi-automatic 4 times Flashing 4 timesA1 Automatic 1 5 times Flashing 5 timesb Semi-automatic “b” 6 times Flashing 6 timesc Dead man 7 times Flashing 7 times6.3.4 SECOND LEVEL PROGRAMMINGTo enter the 2nd level menu, press the SW2 SPEED push-buttonfor more than 2.5 seconds.Both SETUP LEDs light on with steady beam. In this mode, theSPEED key has the menu scrolling function. You can scroll themenu by pressing it the same number of times shown for theparameter.The different menus are identified by the number of flashingof LD8.The LOGIC key is used to set the parameter value. You can exitthe 2nd level menu by pressing the SPEED key for 2.5 seconds.(default settings in bold)* With menus 6 and 7, keep the LOGIC push-button pressed until reaching the time to be set.The time can be set between 0 and 4.25 minutes.ENGLISH