FAAC E024S User Manual

Also see for E024S: Manual Manual

Contents

FAAC E024S User Manual Manual pdf 12 page image

E024S 12 732642 - Rev. Fa10 MM16 MM16 MM8.3.1 REMOTE MEMORY STORAGE OF RC/LC RADIOCONTROLSOther radio controls can be remotely stored only with the RC/LCradio controls, i.e. without using the LOGIC-SPEED-SETUP push-buttons, but using a previously stored radio control.1. Get a radio control already stored on one of the 2 channels(OPEN A or OPEN B).2. Press and hold down push-buttons P1 and P2 simultaneouslyuntil both the LEDs flash slowly for 5 sec.3. Within 5 sec. press the push-button of the radio control that hadbeen memory stored to enable learning on the selectedchannel.system is free of any obstacle created bypersons or things.To add other radio controls, transfer the code of thememory-stored push-button of the radio control to the relevantpush-button of the radio controls to be added, observing thefollowing procedure.• On the memory stored radio control, simultaneously pressand hold down push-buttons P1 and P2.• The radio control LED begins to flash.• Release both push-buttons.• Press the memory stored push-button and hold it down(the radio control LED lights up on steady beam).• Bring the radio controls near, press and hold down thepush-button of the radio control to be added, releasingit only after the double flash of the radio control LED,which indicates memory storage executed.• Quickly press twice the push-button of the memory storedradio control.The automated system performs one openingoperation. Make sure that the automatedsystem is free of any obstacle created bypersons or things.8.3 MEMORY STORAGE OF RC/LC RADIO CONTROLSA maximum of 250 codes can be memorystored, split between OPEN A and OPEN B.1. Use RC/LC remote controls only with receiver module at 433MHz.2. Press the LOGIC (SW3) or SPEED (SW2) push-button, to memorystore respectively total opening (OPEN A) or partial opening(OPEN B), and as you hold it down, also press the SETUP (SW1)push-button. The relevant LED starts to flash slowly for 5 sec.3. Release both push-buttons. Within these 5 sec., press theappropriate push-button on the RC or LC remote control.4. The LED lights up on steady beam for 1 second, indicatingmemory storage executed, and then resumes flashing foranother 5 sec., during which another radio control (point4) can be memory stored.5. When the 5 sec. have elapsed, the LED goes OFF indicatingthe end of the procedure.6. To add other radio controls, repeat the operation at point 1.4. The LED on the board relating to the channel being learnedflashes for 5 sec., within which time the code of anotherradio control must be transmitted.5. The LED lights up on steady beam for 2 seconds, indicatingmemory storage executed, and then resumes flashing for5 sec., during which other radio controls can be memorystored, and then goes OFF.8.4 RADIO CONTROLS DELETION PROCEDURE1. To delete ALL the input radio control codes, press push-buttonLOGIC (SW3) or SPEED (SW2) and, while holding it down, alsopress push-button SETUP (SW1) for 10 sec.2. The LED relating to the pressed push-button flashes for the first5 sec, and then flashes more quickly for the next 5 sec.3. Both LEDs light up on steady beam for 2 sec and then go OFF(deletion completed).4. Release both push-buttons.This operation is NOT reversible. All codes ofradio controls stored as OPEN A and OPEN B willbe deleted.9 BATTERY KIT OF E024S (OPTIONAL)The buffer battery kit was built for insertion inside the controlboard support.This support (Fig.4 ref.a) was pre-moulded to permit thebattery housing to be opened.1. Remove the board support material covering thebattery housing, cutting the material connections alongthe perimeter.2. Insert the battery in the housing you have just created, andsecure it on the anchoring supports (Fig.5).3. To correctly fasten and connect the control unit to the J11 con-nector, refer to the instructions enclosed with the battery kit.Fig. 4Fig. 5ENGLISH