Menu
Craftsman 139.53876 Owner's Instructions Manual
 |
E/.4/RtS OWNER'SINSTRUCTIONSrFeatures:or use with any 53000 SRT series garage door openerreceiverPersonalized Code: Up to 10,000 possible combinations,Code can easily be changed if desiredOperation: Opener activates when 4-code digits andENTER button are pressed,The keypad will illuminate for 5 seconds at the first push ofany key If wrong numbers are accidentally pressed,correction can be made immediately The ENTER key willtransmit only the last four digits,The keypad will blink for 15 seconds after the code istransmitte& Dudng that time you can STOP or REVERSEdoor travel just by pressing the ENTER key,The Lock feature on openers with premium door controls, isdesigned to prevent operation of the door from p_dabletransmitters However, the door will open and close fromthe door control push button and the Multi-Function KeylessEntryPower Supply: 9 Volt batteryProgramming the CodeWe recommend that you program your personal codenow, before you install the Multi-Function Keyless Entry.Then you CaR test the reception at the mounting locationbefore you proceed further.'_ Lift the cover to access the keypad, Figure 1. Decide on a4-digit code using numbers from 0 to 9 You can use anumber more than once (for example, 4, 0, 4, 1).2. Press the selected code digits on the keypad; then pressand HOLD the ENTER button, and press the SRT buttonon the opener end panel (behind the Control Center forscrewdrive), Figure 2,3 Depending on your opener model, when you Figure 1press the SRT button eitherthe openerlight(s) will flash or the garage doorwill begin to move Retease theENTER buttonThe opener has now tearned theselected code and witl respond to future keypadcommands.To ensure that your portable remote control codeswere not disturbed while you were programming the KeylessEntry, test your remotes and reprogram them if necessary°To change the code In your Keyless Entry at any time,repeat Steps 1--3.GARAGE DOOR OPENER(WITH SRT BUTTON)Green "SRT"ButtonGreen thdical,3rFigure 2 Ligh!% % []Multi-Function Keyless EntryMODEL 139.53876To comply with FCC rules, adjustment or modification of receiver a'ndtot]itartsmltter is prohibited, except I'or changing the code setting and replacing the |transmitIer battery THERE ARE NO OTHER USER SERVICEABLE PARTS JChildren operating or playing with a garage door openercan Injure themselves or others. The garage door couldclose and cause serious Injury or death. Do not allowchildren to operate the door push button(s) or remotecontrol(s).A moving garage door could injure or klll someone underIt. Activate the opener only when you can see the doorclearly, tt is free of obstructions, and Is properly adjusted,............ i ,,,=,,,i iInstallationThe recommended mounting locations for sectional and one-piece doors are shown in Figure 3. You can select anotherlocation if you preler However, the keypad must beinstalled within sight of the door.For a one-piece door, use the optional location shown inthe illustration (on the edge of the door jamb) to avoidinjury as the door swings up and out.Test the reception of theKeyless Entry byoperating your openerfrom the selectedlocation, Change thelocation if necessary.Open the keypad andremove the batterycompartment screw andcover to access thebottom mounting hole(Figure 4)Center the keypad ateye level against the#..Extedor Front Wall1,,Piece orSectional DoorDoer ,Jamb Edge',- (Optiooal Loc_tionIo¢ 1-Piece Door)Door Jamb FaceSECTIONAL DOOR ONLYI'(EYPAD MUST BE INSTALLEDWITHIN StGHT OF THE DOORselected location Mark 4 1/4' up thecentedine from the bottom and drill at/8" pi!ot hole lnstalt top mountingscrew, aIIowJng 1/8" to protrudeabove surface. Position keypad onscrew head and adjust for snug fitWith cover open so bottom mountinghole is visible, use a punch to markhole. Remove keypad and drill 1/8"pilot hole. Replace keypad andcomplete installationwith bottomscrew, using care to avoid crackingplastichousing Do not overtightenReplace the battery coverBattery: The 9 Volt battery should producepower for at least one year Repface whenkeypad illumination becomes dimFigure 3Figure 4© ; 995 Sears Roebuck & Company1t 4A 1970 AIt Rights Reserved Printed in Mexico |
Related manuals for Craftsman 139.53876
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved