Craftsman 113.228000 Owner's Manual

Contents

UNPACKING ANDCHECKING CONTENTS ....... 6 Tailstock ram lock ....................... 137 Tailstock 10ck . ......................... 13ASSEMBLY ............. ...... _..........+ MoUnting Lathe and motor on recommended On : off switch .......................... 13Craftsman bench .......................... 7SpUr and cup center instaliati0n . . • .... ....... 9Off'and on +;witch .... ; . ......... . . , . .., . . 10Check motor rotation , ...................... 12GETTING TO KNOW YOUR WOOD LATHE ....... 13Belt guard lock .......................... 13Index pin ............................. 13Spindle lock hole ........................ t3Tool rest lock .......................... 13Tool rest base lock ....................... 13Handwheel ............................ 13Spur center and cup center (aligning centers) ...... 14Tailst0ck .............................. 14Speed chart ............................ 15BASIC LATHE OPERATION .................. 15Changing speeds ......................... 15Spindle turning ......................... 16Indexing .............................. 18MAINTENANCE .......................... 19LUBRICATION ........................... 19RECOMMENDED ACCESSORIES .............. 21REPAIR PARTS .......................... 22TOOLS NEEDED318-inch wrench +;,.iScrewdriver {medium) I ="7/16-inch wrench Framin s are +__I_.?,T,yrtT.++ _L?.'t ? :._',.",+_.:tA'.t t " t .+;,+:;.,.L-L.J.Model 113.228000 Wood Lathe is shipped complete inone carton (without motor, or bench). The V-Belt andmotor pulley are furnished,Model ! 13.228160 Wood Lathe is shipped complete inone carton and includes a Motor.AG\FSeparate all parts from packing materials and check eachone with the "Table of Loose Parts" to make certain allitems are accounted for, before discarding any packingmaterial.If any parts are missing, do not attempt to assemble thelathe olug in the power cord or turn the switch on until themissing parts are obtained and are installed correctly.Using a 7/16" wrench, remove the wood blocks attached tothe Lathe. Save the nuts, bolts and washers, you wilt needfor attaching the Lathe to the bench.Remove the protective oil that is applied to the bed. Useany ordinary household type grease and spot remover.CAUTION: Never use gasoline, naptha or similarhighly volatile solvents.Apply a coat of automobile wax to the bed, Wipe all partsthoroughly with a ciean dry cloth,MOTOR INCLUDED WiTHModel 113.228160itemBACDEFTable of Loose Parts Qty.Motor Pulley : '. .... i, .' ...... '. +' .... 1Belt, "Vee t/2 × 37 .... + ........... 1Wood Turning Lathe ................ 1Owner's Manua4 ................... 1Belt Guard Assembly ................ 1Loose Parts Bag -- Part No. 70046Containing the following: 1Wrench, Hex 5/32.Wrench, Hex3/16,1_iiil; _i_ i ii _; 1Screw, Type 23Pan 10-32 x 3/8 ...... 4Nut+ Hex 3/4-t6 ................. tSpur, Center ................... 1item Table of Loose Parts Qty.Cup, Center .................... 1Point, Center ................... 2Lockwasher Ext. Tooth No. 10 ....... 4Key, Switch .................... 1Clamp Cord .................... 2Bolt Rd. Hd. Carriage 1/4-20 x 1-3/4 . . , 4Washer t7/64 x 47/64 x t/16 ........ 4Nut Hex 1/4-20 ................. 4ScrewPan Hd. Ty. ANo. 8x 1/2 ...... 46" Tool Rest ..................... 1Booklet, How To OperateYour Craftsman Lathe ............. 1