OneStart

Menu

Baicells Nova-436Q Installation Manual

Also see for Nova-436Q: Installation guideInstallation guideInstallation guide

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Contents
  1. installation guide
  2. about this document
  3. safety information
  4. Table Of Contents
  5. Table Of Contents
  6. Overview
  7. Features
  8. LEDs & Interfaces
  9. Location & Environment
  10. CloudCore Account
  11. Install GPS Antenna
  12. Figure 3–4: Attach Bracket to Pole
  13. Install on Wall
  14. Connect GPS Antenna Cable
  15. Connect Ground Cable
  16. Power on to Check LED Status
  17. Basic Configuration Overview
  18. Configure Network Interfaces
  19. Figure 3–15: LGW
  20. Figure 3–16 LGW = Router
  21. Configure the Management Server
  22. Configure Quick Settings
  23. Configure Carrier Setting
  24. Verify eNB Operational Status
  25. Appendix A: Technical Specifications
  26. environmental specifications
  27. Appendix B: Regulatory Compliance
Baicells Nova-436Q Installation Manual Manual pdf 14 page image
14Grounding cable requirement: The grounding cable must connect to the grounding point. The grounding cable must be separated from the signal cables, of enough distance toavoid signal interference.3.4.2 Connect GPS Antenna Cable1. Insert the GPS jumper into a cold shrink tube.2. Connect one end of the GPS jumper to the GPS antenna.3. Push the cold shrink tube to the top joint, and pull out the strip.4. Connect the other end of the GPS jumper to the GPS interface on the eNB, which alsoneeds weatherproof protection.3.4.3 Connect RF Cable1. Open the dust caps of the ANT0, ANT1, ANT2, and ANT3 interfaces.2. Insert the RF cables into cold shrink tubes.3. Connect one end of the 2 RF cables to the ANT0, ANT1, ANT2, and ANT3 interfaces onthe eNB, and tighten them with a wrench.NOTE: When the Nova-436Q is operating in dual carrier (split) mode (futuresoftware upgrade), Cell 1 uses ANT2 and ANT3 and Cell 2 uses ANT0 and ANT1.4. Push the cold shrink tube to the top joint, and pull out the strip.5. Connect the other end of the RF cables to the external antennas, which also needweatherproof protection.3.4.4 Connect WAN Interface Cable1. Unscrew the 3 screws on the cover of the eNB’s wiring cavity using an M4 crossscrewdriver. Open the wiring cavity.2. Connect the cable to the copper or optical interface in the wiring cavity.3. Lay the cable along the wire groove, and stretch it out of the wiring cavity.3.4.5 Connect Ethernet Cable1. Connect the Ethernet cable to the ETH interface in the wiring cavity.2. Lay the Ethernet cable along the wire groove, and stretch it out of the wiring cavity.3.4.6 Connect Power ConnectorSince the length of cable needed for power varies from site to site, the two ends of the poweradaptor are bare terminal ends. You will need to make the power cable according to the actualmeasurements of the installation site, and assemble the power plug and power terminal onthe two ends of the power adaptor.Strip .47in/12mm insulating layer with a wire stripper. The power cord length should be keptbelow 330 ft/100m. The connection steps for the power cable are as follows.
/ 29
Related manuals for Baicells Nova-436Q
Baicells EP3011 Installation & Configuration Manual first page preview
Baicells EP3011 Installation & Configuration Manual
Baicells ATOM OD06 CPE Installation & Configuration Manual first page preview
Baicells ATOM OD06 CPE Installation & Configuration Manual
Baicells Atom R9 User Manual first page preview
Baicells Atom R9 User Manual
This manual is suitable for:
Nova-436Q
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved