ABB TZIDC-200 Operating Instructions Manual

Also see for TZIDC-200: Manual Manual Commissioning instructions Operating instruction Operating instruction

ABB TZIDC-200 Operating Instructions Manual Manual pdf 42 page image

Specifications42 TZIDC-200, TZIDC-210, TZIDC-220 42/18-85-EN9.1.10 AccessoriesMounting materialAttachment kit for linear actuators to DIN / IEC 534 / NAMURAttachment kit for part-turn actuators to VDI / VDE 3845Attachment kit for integral mounting to control valvesAttachment kit for actuator-specific attachment upon requestEx d cable entryCable gland and pipe plug approved for Ex d, securing adhesivePressure gauge blockWith pressure gauges for supply and output pressure. Pressuregauges with housing ø 28 mm (1.10 inch), with connection block inaluminum, black with installation material for mounting on positionerFilter regulatorAll metal version in brass, varnished black, bronze filter element,40 μm, with condensate drain.Max. pre-pressure 16 bar (232 psi), output adjustable to 1.4 ... 6 bar(20.31 ... 87.02 psi)PC adapter for communicationLKS adapter f. plug conn. to positionerFSK modem for HART communication(see data sheet 63_6.71)PC software for remote configuration and operationDSV401 (SMART VISION) with DTM for TZIDC / TZIDC-200available on CD ROM (see data sheet 63_1.20)9.2 TZIDC-2109.2.1 CommunicationProfiles Profibus PA profile for processdevicesElectro-pneumatic actuators V3.0Block types 1 AO Functional block1 Transducer block1 physical blockPhysical Layer In compliance with IEC 61158-2Transmission rate 31.25 Kbit/sSupply voltage Power feed from the PA bus,9.0 ... 32.0 V DCMax. permissible voltage 35 V DCPower consumption 10.5 mACurrent in the event of anerror 15 mA (10.5 mA + 4.5 mA)9.2.2 DescriptionDevice name TZIDC-X10PNO ID no. 0x0639Dev. ID 0X3200028xyzBus address Between 0 and 126, default address1269.2.3 OutputRange 0 ... 6 bar (0 ... 90 psi)Air capacity at 1.4 bar (20 psi) supply pressure5.0 kg/h = 3.9 Nm 3 /h = 2.3 scfmat supply pressure of 6 bar (90 psi)13 kg/h = 10 Nm 3 /h = 6.0 scfmOutput function For single or double-acting actuators,air is vented from actuator or actuatoris blocked in case of (electrical) powerfailureShut-off values end position 0 % = 0 ... 45 %end position 100 % = 55 ... 100 %9.2.4 TravelSteRotation angleUsed range25 … 120° rotary actuators, optionally 270°25 … 60° linear actuatorsTravel timeprolongationSetting range 0 ... 200 seconds, separately for eachdirection9.2.5 Air supplyInstrument air free of oil, water and dust acc. toDIN / ISO 8573-1pollution and oil content according toClass 3 (purity: max. particle size:5 μm, max. particle density:5 mg / m 3 ; oil content: max.concentration: 1 mg / m 3 ; pressuredew point: 10 K below operatingtemperatureSupply pressure 1.4 ... 6 bar (20 ... 90 psi)IMPORTANT (NOTE)Do not exceed the maximum operating pressure of theactuator!Air consumption < 0.1 kg/h / 0.05 scfm (independentof supply pressure)