OneStart

Menu

Siemens SIWAREX WP231 manuals

SIWAREX WP231 first page preview

SIWAREX WP231

Brand: Siemens | Category: Control Systems
SIWAREX WP231 first page preview

SIWAREX WP231

Brand: Siemens | Category: Scales
Table of contents
  1. Table Of Contents
  2. Table Of Contents
  3. Table Of Contents
  4. Table Of Contents
  5. Table Of Contents
  6. Table Of Contents
  7. Table Of Contents
  8. Table Of Contents
  9. Table Of Contents
  10. Introduction
  11. Safety notes
  12. Description
  13. Area of application
  14. System integration in SIMATIC
  15. Customer benefits
  16. Application planning
  17. Parameter assignment options
  18. Parameter assignment with a SIMATIC Panel
  19. Mounting
  20. Coupling mechanisms
  21. Mounting on the SIMATIC S7-1200
  22. Overview
  23. V connection
  24. Shield connection
  25. Figure 6-4 Connection of strain gauge load cell(s) with 4-wire system
  26. Figure 6-5 Connection of strain gauge load cell(s) with 6-wire system
  27. Connection of digital outputs (4 x DQ)
  28. Connection of digital inputs (4 x DI)
  29. Connection of the analog output (1 x AQ)
  30. Connection of RS485 serial interface
  31. Connection of Siebert display via RS485
  32. Connection of the Ethernet interface
  33. Activation of write protection
  34. Mounting of the calibration protection plate
  36. Factory setting of the mode selector
  37. minute quick start with the operator panel and the Ready-for-Use software
  38. Standard parameter settings
  39. Selecting the calibration method
  40. Defining the calibration weights
  41. Setting calibration points
  42. Calibrating the scale automatically
  43. Performing the automatic calibration
  44. minute quick setup with SIWATOOL
  45. Input of required parameters
  46. Receive all data
  47. Service with the SIWATOOL program
  48. Offline parameter assignment
  49. Entering a known SIWAREX IP address
  50. Available help options
  51. Recording scale traces
  52. Firmware update
  53. Figure 7-13 Downloading the firmware with SIWATOOL
  54. Reading out the saved scale logs
  55. Parameters and functions
  56. DR 2 command code
  57. Scale name
  58. Minimum weighing range
  59. Zero by power-on when tare ≠ 0
  60. Weight simulation
  61. Maximum negative zero setting limit (semi-automatically)
  62. Standstill range
  63. Standstill waiting time
  64. Low-pass filter limit frequency (commissioning)
  65. Minimum display size [%]
  66. Calibration procedure
  67. Automatic calibration
  68. DR 4 Output of calculated calibration digits
  69. DR 5 zeroing memory
  70. Effective tare weight - from specification 1, 2 or 3
  71. DR 6 limit value settings
  72. Limit value 1 ON, limit value 2 ON, limit value 1 OFF, limit value 2 OFF
  73. Limit value "Empty" ON
  74. DR 7 interface parameters
  75. Input filtering (hardware setting)
  76. Response of digital outputs to faults or SIMATIC STOP
  77. Analog output range
  78. Output value following fault or SIMATIC STOP
  79. Table 8- 8 Assignment of data record 8
  80. Table 8- 9 Assignment of data record 9
  81. DR 9 module information
  82. DR 10 load cell parameters
  84. DR 12 Ethernet parameters
  86. DR 13 RS485 parameters
  88. DR 14 SIMATIC interface parameters
  90. DR 15 tare settings
  94. DR 18 digital output control specifications
  96. DR 30 current process values
  97. Gross process weight
  98. DR 31 advanced current process values
  99. Refresh counter for process values
  101. DR 32 display of data and operator errors
  103. DR 34 ASCII main display value
  106. DR 46 protocol contents
  107. Unit of weight
  108. DR 47 logbook
  109. DR 48 date and time 2 (for Modbus)
  110. Message types
  111. Evaluating messages with the help of SIWATOOL
  112. System status message list
  113. Messages by LEDs on the module
  114. Command lists
  116. Command groups of the SIWAREX WP231
  117. Communication
  118. Creating the hardware configuration
  119. Calling of function block
  120. Working with the function block
  121. I/O interface of function block
  122. Error codes of function block
  123. Communication via Modbus
  124. Data record concept
  125. Reading registers
  126. Writing registers
  127. Operation requiring verification
  128. Parameterization of the scale
  129. Verification
  130. Checking of parameters relevant to the device
  131. Technical data
  132. Table 13- 10 Technical specifications
  133. Table 13- 11 Technical specifications: Mechanical requirements and data
  134. Electrical, EMC and climatic requirements
  135. Table 13- 13 Requirements: Interference emission in industrial area in accordance with EN 61000-6-4
  136. Table 13- 14 Requirements: Interference immunity in industrial area in accordance with EN 61000-6-2
  137. Table 13- 15 Operating conditions in accordance with IEC 60721
  138. Approvals
  139. Accessories
  140. A.1 ESD Guidelines
  141. Index
Related products
SIWAREX JBSIDOORSIMATICSIJECT15SIJECT16SIMOTIONSICAM MICSINAUT ST7SICAM RTUSIMADYN D
Siemens categories
Industrial Equipment
Controller
Control Unit
Circuit breakers
Switch
Hob
Oven
Measuring Instruments
Washer
Relays
More Siemens categories
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved