Cambium PMP 450 SM manuals

PMP 450 SM

Brand: Cambium | Category: Wireless Access Point

Table of contents

1. Table Of Contents
2. Table Of Contents
3. Table Of Contents
4. Table Of Contents
5. Table Of Contents
6. Table Of Contents
7. Alignment Tone
8. Logs
9. About This User Guide
10. Purpose
11. Cross references
12. Important regulatory information
13. Canada specific information
14. Renseignements specifiques au Canada
15. EU Declaration of Conformity
16. Training
17. Problems and warranty
18. Security advice
19. Warnings, cautions, and notes
20. Caring for the environment
21. Overview of the 450 Platform Family
23. Ethernet interface
24. Supported interoperability for 450m/450i/450b/450 Series
25. Typical deployment
26. Product variants
27. Wireless operation
28. Encryption
29. System management
30. Remote Authentication Dial-in User Service (RADIUS)
31. Wireless Manager (WM)
32. cnMaestro™
33. Radio recovery mode
34. Point-to-Multipoint (PMP)
35. Backhaul (PTP)
36. Platform Family interfaces
37. ATEX/HAZLOC variants
38. Diagnostic LEDs
39. Power supply options
40. ODU mounting brackets & accessories
41. ODU interfaces
42. PMP/PTP 450i
43. PMP 450b
44. Cabling
45. Outdoor copper Cat5e Ethernet cable
46. SFP module kits
47. Main Ethernet port
48. Lightning protection unit (LPU) and grounding kit
49. Cable grounding kit
50. Antennas and antenna cabling
51. RF cable and connectors
52. GPS synchronization
53. CMM5
54. CMM5 Controller Module
55. CMM5 Injector Module
56. CMM5 Specifications
57. CMM4 (Rack Mount)
58. CMM4 (Cabinet with switch)
59. CMM3/CMMmicro
60. Installing a GPS receiver
61. Mounting the GPS receiver
62. Cabling the GPS Antenna
63. Ordering the components
64. ODU with PoE interface to PSU
65. Site planning
66. Power supply site selection
67. ODU and external antenna location
68. ODU wind loading
69. Type approvals
70. Lightning Protection Unit (LPU) location
71. Equipment Disposal
72. Analyzing the RF Environment
73. Obstructions in the Fresnel Zone
74. Multiple OFDM Access Point Clusters
75. Considerations on back-to-back frequency reuse
76. PMP 450m Series planning
77. Link planning
78. Calculating Link Loss
79. Calculating Fade Margin
80. Planning for connectorized units
81. Data network planning
82. DNS Client
83. Developing an IP addressing scheme
84. Allocating subnets
85. Engineering VLANs
86. Network management planning
87. Security planning
88. Planning for HTTPS operation
89. Managing module access by passwords
90. Planning for RADIUS operation
91. port configuration
92. Encrypting downlink broadcasts
93. Allowing management from only specified IP addresses
94. Controlling PPPoE PADI Downlink Forwarding
95. Remote AP Deployment
96. Remote AP (RAP) Performance
97. Example Use Case for Passing Sync
98. Physical Connections Involving the Remote AP
99. Passing Sync signal
100. Wiring to Extend Network Sync
101. Definitions
102. Conditions of use
103. Title and restrictions
104. Right to use Cambium's name
105. Disclaimer
106. Term of license
107. Compliance with safety standards
108. Hazardous location compliance
109. Compliance with radio regulations
111. Brazil specific information
112. Hazardous locations
113. Powering down before servicing
114. Siting ODUs and antennas
115. Preparing for installation
116. Preparing tools
117. Testing system components
118. factory default configuration
119. Configuring Link for Test
120. Logging into the web interface – AP/SM/BH
121. Mount the ODU, LPU and surge suppressor
122. Attach ground cables to the ODU
123. Mount the ODU on the mast
124. Mount the top LPU
125. PMP/PTP 450 Series
126. General protection installation
127. basic requirements
128. Installing the copper Cat5e Ethernet interface
129. Install the bottom LPU to PSU drop cable
130. Installing external antennas to a connectorized ODU
131. PMP 450 Series
132. Troubleshooting
133. PMP 450i Series AP 900 MHz
134. PMP 450 Series SM 900 MHz
135. Installing an integrated ODU