ABB ACS580-07-0870A-4 manuals

ACS580-07-0870A-4

Brand: ABB | Category: Controller

Table of contents

1. Table Of Contents
2. Table Of Contents
3. Table Of Contents
4. Table Of Contents
5. Table Of Contents
6. Table Of Contents
7. Table Of Contents
8. Contents of this chapter
9. General safety in installation, start-up and maintenance
10. Electrical safety in installation, start-up and maintenance
11. Additional instructions and notes
12. Grounding
13. Additional instructions for permanent magnet motor drives
15. Related manuals
16. Terms and abbreviations
18. Single-line circuit diagram of the drive
19. Cabinet layout – bottom entry and exit of cables
20. Overview of power and control connections
21. Door switches and lights
22. Control panel
23. Degree of protection
24. UK gland/conduit plate (option +H358)
25. Type designation key
27. Necessary tools
28. Moving and unpacking the drive
29. Unpacking the transport package
30. Lifting the cabinet
31. Moving on rollers
32. Installing the IP54 roof
33. Attaching the cabinet to the floor and wall or roof
34. Attaching methods
35. Miscellaneous
37. Protecting the motor insulation and bearings
38. Requirements table
39. Additional requirements for ABB high-output and IP23 motors
40. Additional data for calculating the rise time and the peak line-to-line voltage
41. Typical power cable sizes
42. Recommended power cable types
43. Selecting the control cables
44. Separate control cable ducts
45. Implementing thermal overload and short-circuit protection
46. Protecting the drive against ground faults
47. Implementing the Power-loss ride-through function
48. Using a contactor between the drive and the motor
49. Example bypass connection
50. Switching the motor power supply from direct-on-line to drive
51. Connecting a motor temperature sensor to the drive I/O
53. Motor and motor cable
54. Connecting the power cables
55. Layout of the input and motor cable connection terminals (frames R10 and R11)
56. Grounding the motor cable shield at the motor end
57. Grounding the outer shields of the control cables at the cabinet lead-through
58. Routing the control cables inside the cabinet (frames R10 and R11)
59. Connecting the emergency stop push buttons (options +Q951)
60. Setting the voltage range of the auxiliary control voltage transformer (T21)
61. Installing option modules
63. Layout
64. Default I/O connection diagram
65. Switches
66. NPN configuration for digital inputs (DIGITAL IN)
67. DI6 as frequency input
68. Safe torque off (STO)
69. Technical data
72. Start-up with the First start assistant on an assistant panel
75. Descriptions of symbols
76. Cleaning the air inlet (door) meshes (IP42 / UL Type 1 Filtered)
77. Replacing the air filters (IP54 / UL Type 12)
78. Heatsink
79. Replacing the cabinet fan
80. Replacing the drive module main fans
81. Replacing the circuit board compartment cooling fan
82. Replacing the IP54 (UL type 12) roof fan
83. Replacing the drive module
84. Capacitors
85. Replacing the battery in the assistant control panel
87. Definitions
88. Altitude derating
89. Dimensions and weights
90. Losses, cooling data and noise
91. Terminal data for the control cables
92. Electrical power network specification
93. Ambient conditions
94. Auxiliary circuit power consumption
95. CE marking
96. Declaration of Conformity (Safe torque off)
97. Compliance with the EN 61800-3:2004
98. Cyber security disclaimer
100. Compliance with the European Machinery Directive
101. Grounding of protective shields
102. Single drive (external +24 V DC power supply)
103. Multiple drives (internal power supply)
104. Multiple drives (external power supply)
105. Operation principle
106. Maintenance
107. Safety data (SIL, PL)
108. Abbreviations
111. Electrical installation
112. Start-up
113. LEDs
114. CMOD-01 multifunction extension module (external 24 V AC/DC and digital I/O)
119. Safety instructions
123. Diagnostics
124. Product and service inquiries