OneStart

Menu

red lion Sixnet Series Hardware Manual

Also see for RAM 9000: Hardware guide

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. Preface
  4. Trademark Acknowledgments
  5. Additional Product Information
  6. Statement of Limited Warranty
  7. Chapter 1 Product Overview
  8. Specifications
  9. RAM 9000 Model Comparison Chart
  10. Power Specifications and Consumption
  11. Indicator Lights
  12. Bootup LED Sequence
  13. Mode/Reset Button functions
  14. Ordering Guide
  15. Chapter 2 Hardware Installation
  16. Mechanical Dimension Diagrams
  17. Cellular Antenna and Cable Specifications
  18. GPS Antenna
  19. Wi-Fi Antenna
  20. USB Device Cable
  21. RS485 Wiring Diagram
  22. Power Source
  23. Power Input Diagram
  24. Battery Removal and Installation
  25. SIM Cards
  26. I/O Wiring
  27. I/O Wiring Diagram
  28. Equivalent Circuit Diagrams
  29. Cleaning
  30. Service and Support Information
red lion Sixnet Series Hardware Manual Manual pdf 18 page image
RAM 9000 Series Hardware Guide 5-23Product Overview Revised 2015-07-16SpecificationsBootup LED SequenceStage 1: Power OnWhen the unit is first powered on, the P1/P2 LEDs will indicate that power has been detected.Stage 2: CPU InitializedThe LED stacks on each side of the unit will scroll rapidly. When initialization is complete, all front LEDs will be on.Stage 3: Kernel LoadingThe Reset LED will turn off, but Status, A, B and RS232 will remain on.Stage 4: Filesystem MountedThe Status and RS232 LEDs will turn off and go into normal mode. A and B will remain on.Stage 5: System services startingThe A and B lights will now turn off. All front panel LEDs should be in normal mode operation. Your unit should befully functional within a few seconds.Data Interface Specifications: Serial, Ethernet & USBEthernet PortThe unit’s 10/100Mbps port is compliant with the EIA-568 standard. The modem’s ports are auto-sensing so theycan be used with either a straight or crossover RJ45 cable to connect to host ports.The RAM-9701 model has one Ethernet port and the RAM-9711, RAM-9731, RAM-9911, and RAM-9931 modelshave two Ethernet ports.DO1/DO2 ON The corresponding discrete output is ON and sourcing power.OFF The corresponding discrete output is OFF and not sourcing power.DI1/DI2ON A valid voltage is detected on the corresponding discrete input.OFF A valid voltage is not being detected on the corresponding discreteinput.A Future Reserved for future use.B Future Reserved for future use.Ethernet Plug &Connector Pin PositionsLED STATUS CORRESPONDING STATE
/ 40
Related manuals for red lion RAM 9000
red lion DA USB Sled Installation Manual first page preview
red lion DA USB Sled Installation Manual
This manual is suitable for:
RAM 9000RAM-9631RAM-96x1 SeriesRAM-9731RAM-97x1 SeriesRAM-9931RAM-99x1 SeriesRAM-9x01 SeriesRAM-9x11 SeriesRAM-9x31 SeriesSixnet Series
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved