Menu
red lion IAMS Installation Manuallines
                |
GENERAL DESCRIPTIONThe IAMS3535 Smart Analog to MODBUS Conditioner with Alarmsmodule accepts a wide range of DC analog process signals. There are eighteendifferent DC analog input ranges which determine the input span and type. Theinput accepts a maximum of 110 VDC and 110 mA DC.The IAMS converts an analog input signal into a register format that can beread using ASCII or RTU MODBUS protocol. With the features of gain andoffset, the input signal can be scaled to meet process requirements. Additionally,two setpoint values can be entered for dual relay process monitoring alarms.The IAMS is programmed with Windows™ based SFIMS software. Thesoftware allows configuration, calibration, and storage of IAMS program files.Additionally, all setup parameters can be interrogated and modified throughMODBUS register and coil commands.The RS485 port allows the IAMS to be multidropped, with Baud rates up to38400. The CBPRO007 programming cable converts the RS232 port of a PC toRS485, and is terminated with an RJ-11 connector. The bidirectional capabilityof the CBPRO007 allows it to be used as a permanent interface cable as well asa programming cable.The IAMS’s two Form A relay alarms can be configured independently forabsolute high or low acting with balanced or unbalanced hysteresis. Alarm 2 canalso be configured for deviation and band alarms. In these modes, Setpoint 2tracks Setpoint 1. Adjustable alarm trip delays can be used for delaying outputresponse. The alarms can be programmed for Automatic or Latching. Latchedalarms must be reset via serial command. A standby feature supresses the alarmduring power-up until the process stabilizes outside the alarm region. Standbyeliminates power-up tripping for low acting alarms. The output relays can alsobe manually controlled via register commands.The module’s high density packaging and DIN rail mounting saves time andpanel space. The module is equipped with a universal mounting foot forattachment to standard DIN rails, including top hat (T) profile or G profile rail.SAFETY SUMMARYAll safety related regulations, local codes and instructions that appear in themanual or on equipment must be observed to ensure personal safety and toprevent damage to either the instrument or equipment connected to it. Ifequipment is used in a manner not specified by the manufacturer, the protectionprovided by the equipment may be impaired.ORDERING INFORMATIONSPECIFICATIONS1. POWER: 18-36 VDC, 3.0 W max. or 24 VAC, ± 10%, 50/60 Hz, 4 VA max.2. INPUT DC RANGES:0-20 mV, 0-50 mV, 0-100 mV, 0-200 mV, 0-500 mV, 0-1V, 0-2 V, 0-5 V,0-10 V, 0-20 V, 0-50 V, 0-100 V, 0-2 mA, 0-5 mA, 0-10 mA, 0-20 mA,0-50 mA, 0-100 mA3. MAX. INPUT SIGNAL:Current Input: 110 mA DCVoltage Inputs: Terminal 7: 1 VDC +10%Terminal 8: 10 VDC +10%Terminal 9: 100 VDC +10%4. INPUT RESISTANCE:Current: 10 OhmsVoltage: greater than 100 K5. INPUT PROTECTION: Surge suppressor diodeCurrent Terminal: Protected to 110 mA DC max., 1.1 VDC.100 V Terminal: Protected to 110 VDC.1 V & 10 V Terminal: Protected to 100 VDC for one minute.6. INPUT COMMON MODE REJECTION: 50/60 Hz, 110 dB min.7. ISOLATION LEVEL: 1.5 kV @ 50/60 Hz, 1 min. between input, RS485and power supply. 2300 Vrms, 1 min. to relay contacts.1O ANALOG TO MODBUS CONVERSIONO 18 DIFFERENT DC ANALOG INPUT RANGESO PROCESSOR BASED SCALINGO PC CONFIGURATION SOFTWAREO DUAL SETPOINT RELAY ALARMSO FOUR WAY SIGNAL ISOLATIONMODEL IAMS - INTELLIGENT ANALOG TO MODBUS CONDITIONER W/ ALARMSMODELIAMSDESCRIPTIONSmart Analog to Modbus Conditioner w/AlarmsPART NUMBERIAMS3535CBPROSFIMSProgramming Interface CablePC Configuration Software for WindowsCBPRO007SFIMS-CBJRJ11 to Terminal AdapterCable RJ11 to Unterminated 7 foot lengthDRRJ11T6CBJ11A07Cable RJ11 to RJ11 6 inch jumper CBJ11BD5DIMENSIONS In inches (mm)CAUTION: Read completeinstructions prior to installationand operation of the unit.CAUTION: Risk of electric shock.Bulletin No. IAMS-ADrawing No. LP0475Released 9/01Tel +1 (717) 767-6511Fax +1 (717) 764-0839www.redlion-controls.comUL Recognized Component,File # E179259 |
Related manuals for red lion IAMS
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved