OneStart

Menu

Zaxcom ZFR400 User Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Contents
  1. user manual
  2. Table Of Contents
  3. Table Of Contents
  4. ZFR400
  5. HOME SCREEN
  6. MAIN MENU
  7. SUB MENUS
  8. TIME CODE MENU
  9. T RANSMISSION U NTIL J AMMED
  10. RECORD MENU
  11. ZAXNET MENU
  12. Enable
  13. Before Transmit Time
  14. AUDIO MENU
  15. D YNAMICS
  16. SETUP MENU
  17. Adjust
  18. recording format
  19. FIRMWARE
  20. INPUTTING AUDIO
  21. Input
  22. PRODUCT SUPPORT
  23. SPECIFICATIONS
  24. ZAXCOM WARRANTY POLICY AND LIMITATIONS
Zaxcom ZFR400 User Manual Manual pdf 13 page image
Zaxcom ZFR400 ZaxNet Menu13ZAXNET MENUZaxNet ModeThis menu sets the mode of the ZaxNet transceiver. OFF - The ZaxNet transceiver is disabled. The ZFR400 will not receive ZaxNet commands or time code and itwill not send any ZaxNet audio. Please note if ZaxNet mode is set to OFF the several ZaxNet menu items willnot appear. RX - The ZaxNet transceiver will receive ZaxNet commands and time code.This screen will display what ZaxNet data is being received by the ZFR400. Including total receivedinformation packets, ZaxNet TC received and remote control commands received. This information is usedfor debugging purposes.Please note if the RX to TX Time is enabled the ZFR400 will not be able to be set to RX mode. TX - The ZaxNet transceiver will send ZaxNet confidence audio and time code.ZaxNet Receive Frequency SetThis menu will only appear if ZaxNet is set to receive (RX) modeThe ZaxNet receive frequency is the frequency that the ZFR400 will get its wireless time code and remotecontrol commands on. This frequency will need to match the frequency of the corresponding ZaxNettransmitter. The ZaxNet transmitter can be a QRX with QIFB, Nomad, TRX900CL or IFB100/200. The ZFR400 canalso receive ZaxNet time code from another TRX / ZMT transmitter or a ZFR recorder that is transmittingZaxNet on this frequency. Please keep in mind that the range will be limited when receiving ZaxNet from a TRXor ZFR.When the ZFR400 is receiving a valid ZaxNet signal the signal strength will be shown as well as signal strengthmeter that runs vertically on the far right side of the screen.ZaxNet Transmit Frequency SetThis menu will only appear if ZaxNet is set to transmit (TX) modeThe ZaxNet transmit frequency is the frequency that the ZFR400 will broadcast time code and confidence audioon. Please note the ZaxNet transmitted audio is for quality control purposes and the expected range will be lessthan 20 feet.ZAXNET MODE: TXRX FREQ : 2.403 RXSIGNAL : 28ZAXNET TX FREQ:2.473
/ 29
Related manuals for Zaxcom ZFR400
Zaxcom NOVA User Manual first page preview
Zaxcom NOVA User Manual
This manual is suitable for:
ZFR400
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved