OneStart

Menu

XTA DC1048 Operator's Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Page 41 preview
Page 42 preview
Page 43 preview
Page 44 preview
Page 45 preview
Page 46 preview
Page 47 preview
Page 48 preview
Page 49 preview
Page 50 preview
Page 51 preview
Page 52 preview
Page 53 preview
Page 54 preview
Page 55 preview
Page 56 preview
Page 57 preview
Page 58 preview
Page 59 preview
Page 60 preview
Contents
  1. Operator's Manual DC1048 Integrated Audio Management Page
  3. DECLARATION OF CONFORMITY
  4. Important Safety Instructions
  5. Instructions De Securite Importantes
  6. Thanks
  7. Introduction
  8. Installation
  9. Operation
  10. Front Panel Indicators
  11. USB Connector
  12. Rear Panel Controls, Connections and Indicators
  13. Menus
  14. Remote Control and Initial Set-up
  15. Layout of the Main Window
  16. Timed Presets and Preset Files
  17. Connection of Multiple Units on an RS485 Network
  18. Connection directly to the RS485 Network
  19. Security and Locking
  20. Security in ICORE
  21. The GPI Port
  22. Non-Isolated Connection
  23. Complex Mode
  24. Appendix I: Updating Device Firmware
  25. Appendix II: Limiter Types and Setting Thresholds
  26. Appendix III: Parametric Filter Types and Their Uses
  27. Shelving EQ (High Shelf shown)
  28. Notch Filter
  29. All Pass Filter
  30. Low/High Pass Variable 'Q' Filter (Low Pass shown)
  31. Elliptical filters
  32. Appendix IV: Maintenance
  33. Appendix V: Specifications
  34. Index
XTA DC1048 Operator's Manual Manual pdf 15 page image
Operator’s Manual DC1048 Integrated Audio Management Page 15Rear Panel Controls, Connections and Indicators1: Mains Power Inlet and Power SwitchThe mains fuse is also located here, between the switch and the power socket –only replace with the correct rated fuse.2: RS485 ConnectionTo connect a network of DC1048 units, or to include this unit on a network ofother devices, use this connection. The pin-out of this connector is:Pin 1: Data A (+)Pin 2: Data B (-)Pin 3: Shield/GroundThe procedure for setting up a remote network is explained in detail starting onpage 34 of this manual.3: GPI PortThis port offers a set of input and output connections designed for use with theWP-1048 touch remote, or for connection to other third party remote controlinterfaces, to allow for closed contact preset recall.4: Balanced Audio OutputsThe analogue outputs are wired as:Pin 1: Signal Hot (+)Pin 2: Signal Cold (-)Pin 3: Shield/Ground5: Balanced Audio InputsThe analogue inputs are wired as:Pin 1: Signal Hot(+)Pin 2: Signal Cold (-)Pin 3: Shield/Groundtax Serial No:0000001DC104890V-240V AC50 - 60Hz 30WBALANCED OUTPUTSWARNING: THIS EQUIPMENT MUST BE EARTHED.DO NOT EXPOSE TO RAIN OR MOISTURE.1 2 3 4 5 6 7 8 9 10GPIO PORT1-4: OUTPUT5-8: INPUTS9: +5V / 10: CHASSIS GND11 - 12: ISOLATED GNDCAUTION! SHOCK HAZARD.DO NOT REMOVE COVERS.RS485 ABCD12345678BALANCED INPUTSMANUFACTURED INTHE UK BY tax11 12INSTALLATION AUDIO MANAGEMENTDC10482 3 41 5
/ 60
Related manuals for XTA DC1048
XTA DP448 Operator's Manual first page preview
XTA DP448 Operator's Manual
This manual is suitable for:
DC1048
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved