Whirlpool 1166073 Installation Instructions Manual

4 n Insert the frame in the wallopening. Square the level frame. Nailframe securely to the wall studs.Floor DamageRemove air conditioner from cartonand place on cardboard.Failure to do so may cause damageto floor covering.‘SCl&VS20 n Attach front bv firstremoving the two, #8 x 9?i mm (318”)screws from base; then insert front tabsinto top of cabinet and swing front inplace. Attach bottom of front byreinserting the two screws.16 H Secure vertical and angle THROUGH-THE-WALLINSTALLATIONINSTRUCTIONS . . . FOR SLIDE-OUTCHASSIS MODEL ONLY.supports together. Attach supporti? tobottom of cabinet. But Do Not tiahtenbolts at this time. Attach wall rail toangle supports. Slide each supportassembly toward house until wall rail ispositioned firmly against wall.Note: If your house is constructed ofmaterial that could be damaged bywall-mounting support, fasten a boardbetween wall rail and house.17 I Tighten bolts securely with a11.1 mm (7/16”) socket and socketwrench. Tighten angled support boltslast so wall rail fits tightly against house,It is the customer’s responsibility andobligation to have this product installedby a qualified technician familiar withthrough-the-wall room air conditionerinstallations. apptoptlafeheader If requiredfrhl + casing,w Loosen, but Do Not removegrounding wire screw. Disconnectgrounding wire.\ ‘,\\I II louvers. I IPersonal Injury/ProductDamage HazardInstall window-lock bracket to preventair conditioner from falling out ofwindow.Failure to do so could result inpersonal injury or product damage.thlcknes6 w Pull on handles; slide airconditioner out of cabinet and placeon cardboard.7 n Insert cabinet into wall opening.The top of the cabinet should extend12.7 mm (l/2”) into room. If there is trim,the cabinet should extend 12.7 mm(l/2”) in front of trim.Frame constructionapproptlafeheader If requiredI 254 mm (10’3drainCUDalternateconsftucffonfor plasfetProvide 30 mm(l-3/169 Property DamageCheck that air conditioner cabinet istilted to the outside so that water willrun to the outside.Failure to do so may cause damageto floor covering or wall.provided, placethrough hole incabinet rail as&fe&an&efor \ I I I\\\\power supply carentry on leff dde30 mm (l-3/16”)clearance for18 n Insert window rail seal behind 1 Brick veneer constructionn When using a wood, metal orplastic molding, the finish frame shouldline up with inside wall. If the plasteredwall is to be flush with the cabinet andno molding is used, the finish frame mustbe set 12.7 mm (l/2”) into the wall.the top of the lower window sash andagainst the glass of the upper window.Place window-lock bracket on top oflower window and against upperwindow sash. Use a 2.4 mm (3/32”) drillbit to drill a starter hole through the holein the bracket. Attach window-lockbracket with wood screw. Seal smallopenings around window with gum-type sealer.8 n Place level inside cabinet on theright side. There should be a tilt to theoutside of approximately one bubble.Place the level on the left side andcheck.9 n Use the insulation removed inStep 2 to seal opening between cabinetand frame.10 n Drill four holes on each sideElectrical Shock HazardGrounding wire from the airconditioner must be connected to thecabinet.Failure to do so could result inelectrical shock.and two through the top of the cabinetinto the frame. Use ten #lO x 25.4 mm(1”) wood screws (not provided) toattach cabinet to frame. Do Notovertighten screws or cabinet will distortand provide a poor air seal betweenuse 66 cm-dimension50.2 cm (19-3/4”)(includes allowancefor 12.7 mm (l/2”)flange on b&&m’ ofcabinet).7ul6 Dimensiondepends onwall thicknessand type of19 n Inset-t air conditioner into2 molding.w Cut opening throughthe wall. Remove insulation.3 n Use 25.4 mm (1”) or heavierlumber for wood frame. Measure depthof wall opening and frame.Apply wood preservative to the outsideexposed surface.cabinet. Reattach grounding wire togrounding screw. Put excess groundingwire between coil and grey beadedfoam.Panel C

/ 5

Related manuals for Whirlpool 1166073