Manual No: 577013-801 • Revision: AInstall, Setup, & Operation ManualPressure Management ControlSection 16Pressure Management Control16-i

Site Requirements

Related Manuals

Vapor Pressure Sensor

Circuit Directory

Introduction

PMC Setup

Alarms

Warning Posting

PMC Alarm Summary

PMC Status Report

Connecting Laptop to Console

Figure 9. Connection Description window

Figure 11. Console comm port settings printout example

Sending Console Commands

Figure 13. Vapor Processor Status Report Details - Serial to PC Format

Figure 14. Vapor Processor Runtime Diagnostic Report - Serial to PC Format

Figure 15. Percent Hydrocarbon Diagnostic Report - Serial to PC Format

Automatic Control and Runtime Fault Alarm

Veeder-Root TLS-350R Install, Setup, & Operation Manual

Contractor Certification Requirements

Special Tools Required

Site Considerations - Control Drawing

National Electrical Code Compliance

TLS RF Wireless System Overview

Equipment Dimensions

TLS RF Installation

Wiring the TLS RF

Wireless Component Installation

Mag Sump Sensor Installations - STP Sump

Mag Sump Sensor Installations - Dispenser Pan Sump

Connecting cables to the Transmitter

Receiver Installation

Repeater Installation

Network Setup

Site Startup Procedure

Troubleshooting

Radio Line of Sight

Probe Troubleshooting

Resetting Data in the TLS RF Unit

TLS-350R

System Requirements

Safety Warnings

GENERAL PRECAUTIONS

AST Construction Safe Work Practices

MAG-XL Flex Probe Operating Parameters

Example MAG-XL Flex Probe Site Layout Drawing

MAG-XL Flex Probe Dimensions

Example MAG-XL Flex Probe Installation in Tank Manway

Example MAG-XL Flex Probe Installation in Existing Tank Opening

Component Dimensions

Pre-Installation Component Setup and Functional Check

Unpack the MAG-XL Flex Probe

Assemble the MAG-XL Flex Probe Components

Probe Installation - Top of Tank 2-Inch Pipe Fitting

Install the MAG-XL Flex Probe Assembly

TLS XL-Transmitter Installation - Top of Tank 2-Inch Pipe fitting (ref. Figure 14)

Figure 13. Installing TLS XL-Transmitter - man way riser pipe

Connecting MAG-XL Flex Probe Wiring

Figure 15. Connecting input wiring to transmitter terminal blocks

Height Reading Adjustment

Figure 17. In-tank setup for TLS Consoles used with MAG-XL Flex Probes

TLS Limit Calculations

Figure 18. Alarm Limit Settings

Vertical Tank Volume Calibration

Product Marking Information

safety warnings

safety symbols

Available Kits

Overview

Field Assembling Vac Sensor/Vac Float modules

Figure 3. Attaching four Vac Sensors/Floats to the housing

Figure 4. Vac Sensor/Vac Float tubing connections

Installing Vac Sensor Housing Support Bracket

Attaching Vac Sensor Cables and Tagging Vac Sensor/Vac Float Pairs

Installing Vac Sensor Housing onto Support Bracket

Vacuum Connections to a Double-Wall Vapor Return Line

Vacuum Connections to a Double-Wall Fiberglass Tank

Vacuum Connections to Siphon Port of the Pump

Field Wiring Vac System Connections

Figure 14. Field wiring connections

Connecting Vac Sensor Field Wiring to TLS Console

Figure 17. Connecting Pump Sense & 4-Relay Modules - Red Jacket Pumps

Disable Extended Run Feature in the Pump Controller

ATM Pressure Sensor Setup

Vac Sensor Setup

Performing Vac Sensor Setup

Vacuum Integrity Test Prior to Filling Tank (Optional)

Running a Manual Test

Figure 19. TLS Console Vac Sensor Manual Test

Figure 20. TLS Console Vac Sensor Evac Hold Procedure

installation guide

Business Inventory Reconciliation (BIR)

TLS-350R System Requirements for BIR and ISD

Manifolded Tank Applications

Other Applications

Mechanical Dispenser Interface Module (MDIM Low Voltage Dispenser Interface Module (LVDIM)

International Forecourt Standards Forum Dispenser Interface Module (IFSF) - TLS-350R, TLS-450PLUS

DIM And Installation Kit Ordering Guide

Figure 1. Simplified DIM Connections To Various Dispensing Systems

Bennett POS System

Figure 2. Bennett Pump Fuelomat Dispenser Interface Installation Diagram

Gilbarco TCRG, TCRG2, T-11, and T-12 POS Systems

Wiring Diagram for a Transac Current Loop Interface

Wiring Diagram for an Excentus Current Loop Interface

Gilbarco TS-1000 POS and PAM Systems

Figure 5. Universal Distribution Box Interface

Gilbarco G-Site™ POS Systems

Figure 6. Example G-Site Installations

AutoGas Storemaster and Gilbarco Dispenser Systems

Figure 7. AutoGas 510 CRIND Controller With Current Loop Interface

Figure 8. AutoGas 510 CRIND Controller With Serial Interface

Figure 9. AutoGas 510 CRIND Controller

Figure 10. AutoGas 507 CRIND Controller

Gilbarco SmartCrind Dispenser Systems

Tokheim Dispensing Systems

Figure 12. Tokheim DHC Standalone Installation

Figure 14. Tokheim Dispenser Controller With Single CAB Installation

Wayne Dispensing Systems

Installation Notes

Figure 17. Example CAB Connections In Wayne Nucleus Data Box (TLS-350R Only)

Schlumberger POS Systems

Figure 19. MicroMax POS with Allied Protocol Box Current Loop Interface

Figure 21. MicroMax POS with Tokheim DCHC Controller Box and RS-232 CAB Interface

GasBoy CFN Systems

Figure 23. Gasboy Console Loop Connection

BIR Protocol DIM

Mechanical Dispensers

Figure 25. Wiring Diagram Of TLS-450/TLS-450PLUS MDIM Using Two 1871/7697 Series Pulse Transmitters & Required Barriers

Figure 26. Mechanical Dispenser Applications Using 7874 Series Pulser/Totalizer

Figure 27. TLS-350 Meter Stand Application Using 1871/7697 Series Pulser/Totalizer

Figure 28. TLS-450/TLS-450PLUS Meter Stand Application Using 1871/7697 Series Pulser/Totalizer

LVDIM Applications

Figure 30. TLS-450/TLS-450PLUS LVDIM Installation With PetroVend System 2 Site Controller

Kraus Micon 200 Electronic Dispensers

Figure 32. TLS-450/TLS-450PLUS LVDIM Installation Kraus Micon 200 Series Electronic Dispensers (Not UL Approved)

Wiring to GasBoy 9800 or Tokheim 2600 Series Electronic Dispensers

Figure 34. TLS-450/TLS-450PLUS LVDIM Installation With GasBoy 9800 Or Tokheim 2600 Series Electronic Dispenser Head

TLS-300I/C

TLS-350 PLUS

TLS-350J

TLS2

Veeder-Root TLS-350R Install, Setup, & Operation Manual

Product

Learn More

Legal