Contents - Preface About this manual
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Approvals
- Safety
- Caution
- Grounding and earth fault protection
- Electro-magnetic compatibility (EMC)
- Receiving the delivery
- Type designation code
- Lifting the frames MR8 and MR9
- Accessories
- Frame MR4
- Frame MR6
- Frame MR7
- Frame MR9
- Mounting
- Wall mounting of MR5
- Wall mounting of MR6
- Wall mounting of MR7
- Wall mounting of MR8, IP21 and IP54
- Wall mounting of MR8, IP00
- Wall mounting of MR9, IP21 and IP54
- Wall mounting of MR9, IP00
- Dimensions for wall mounting, North America
- Wall mounting of MR5, North America
- Wall mounting of MR6, North America
- Wall mounting of MR7, North America
- Wall mounting of MR8, North America
- Wall mounting of MR8, UL Open Type, North America
- Wall mounting of MR9, North America
- Wall mounting of MR9, UL Open Type, North America
- Flange mounting of MR4
- Flange mounting of MR5
- Flange mounting of MR6
- Flange mounting of MR7
- Flange mounting of MR8
- Flange mounting of MR9
- Dimensions for flange mounting, North America
- Flange mounting of MR5, North America
- Flange mounting of MR6, North America
- Flange mounting of MR7, North America
- Flange mounting of MR8, North America
- Flange mounting of MR9, North America
- Cooling
- Power cabling
- UL standards on cabling
- Cable and fuse sizes, North America
- Brake resistor cables
- Preparing for the cable installation
- Frames MR8 to MR9
- Installation in a corner-grounded network
- Control unit
- Control unit cabling
- Control terminals and DIP switches
- Fieldbus connection
- Using fieldbus through an Ethernet cable
- Using fieldbus through an RS485 cable
- Installation of option boards
- The installation procedure
- Installation of a battery for the Real Time Clock (RTC)
- Commissioning and additional instructions
- Operation of the motor
- Installation in a marine environment
- The EMC jumper in MR7
- The EMC jumper in MR8
- The EMC jumper in MR9
- Maintenance
- Technical data, Vacon ® 100
- Mains voltage 380-500 V
- Mains voltage 525-600 V
- Mains voltage 525-690 V
- Brake resistor ratings
- Vacon ® 100 - technical data
- Technical data, Vacon ® 100 FLOW
- Vacon ® 100 FLOW - technical data
- Technical data, Vacon® 100 HVAC
- Overload capability
- Vacon ® 100 HVAC - technical data
- Technical data on control connections
|
EC DECLARATION OF CONFORMITYWeManufacturer’s name: Vacon OyjManufacturer’s address: P.O. Box 25Runsorintie 7FIN-65381 VaasaFinlandhereby declare that the productProduct name: Vacon 100 AC driveModel Designation: Wall-Mounted Drives:Vacon 0100 3L 0003 2...0310 2Vacon 0100 3L 0003 4...0310 4Vacon 0100 3L 0003 5...0310 5Vacon 0100 3L 0004 6...0208 6Vacon 0100 3L 0007 7...0208 7IP00 Drives:Vacon 0100 3L 0140 2...0310 2Vacon 0100 3L 0140 5...1180 5Vacon 0100 3L 0080 6...0820 6Vacon 0100 3L 0080 7...0820 7Enclosed Drives:Vacon 0100 3L 0140 5...0590 5Vacon 0100 3L 0080 7...0820 7has been designed and manufactured in accordance with the followingstandards:Safety: EN 61800-5-1: 2007EN 60204-1: 2009 (as relevant)EMC: EN 61800-3: 2004 + A1: 2012EN 61000-3-12and conforms to the relevant safety provisions of the Low VoltageDirective (2006/95/EC) and EMC Directive 2004/108/EC.It is ensured through internal measures and quality control that theproduct conforms at all times to the requirements of the currentDirective and the relevant standards.In Vaasa, 31st of March, 2015Vesa LaisiPresidentThe year the CE marking was affixed: 2009APPROVALS VACON · 924-HOUR SUPPORT +358 (0)201 212 575 · EMAIL: VACON@VACON.COM 1
|
