Menu
USP AD-2000 Owner's Manual
                  | |
13Programming Example for Quick SetupBefore programming the dialer, study the example shown on this page.This “quick setup” example programs in one telephone number, twonumeric pager numbers, two attempts, two repeats, an ID plus twoadditional OGMs, and channels 1 and 4.Once you understand the setup, use the blank Program Planner onpage 14 to begin programming your dialer. We recommend makingseveral blank copies of the Planner before beginning the process. Italso is advisable to fill in the Planner in pencil initially.STEP 1 Press “1”.STEP 2 When the LCD re ads SELECT 1-8, press “1” to install thefirst phone number in location 1 press “2” to indicate no pager; thenpress, in sequence, (fictitious) phone number “2345678” followed bythe “*” sign to store the programming process for that number.STEP 3 Press “5” to install the second phone number in location 5;press “1” to indicate numeric pager; then press’ in sequence,“3456789PP4455#” followed by the “*” sign. The first seven digitsrepresent the pager number dialed; each P stands for a 2-second pause;the next four digits followed by the # sign represent the pager codeand the * stores the programming process for that number.Now press “6” to install the third phone number in location 6; press“1” to indicate numeric pager; then press, in sequence,“3456789PP5544#” followed by the “*” sign.STEP 4 Press “0” to exit PROGRAM NUMBERS.STEP 5 At the PROGRAM: T -LINE prompt, press “1” to choosetone; press “2” to indicate no PBX; press “2” to program in twodialing attempts per emergency number called; press “2” to programin two message repeats for each call.STEP 6 Press “1” to PROGRAM OGM(S). Press “2” three times toScroll to option #4; press “1” to program in an ID message and twospecific outgoing messages (OGMs).STEP 7 Using a prepared script and speakin g six-to-eight inchesfrom the dialer’s microphone on the front of the unit, press “R” whenyou are ready to enunciate your 15-second identification message andyour two 18-second messages. Dialer automatically prompts to nextOGM. Make OGM1 a message telling the receiving party to call thepolice department. Make OGM2 a message to call the fire department.STEP 8 Press “1” to play back all recorded messages; press “1” againto accept. (NOTE: DIALER LCD WILL ONLY SHOWPROGRAMMED NUMBERS AND OGM OPTIONS).STEP 9 Press “1” to PROGRAM CHANNELS.STEP 10 Press “1” to program Channel 1. Press “1” to ENABLE.Press “1” then enter “30” then press “*” for a 30-second EXIT delay;press “1” then enter “15” then press “*” for a 15-second entry delay.Now press “2” for NORMALLY CLOSED and then “1” forMOMENTARY activation. Press “1” to select phone/pager number 1 tobe dialed. Press “1” again to select phone/pager number 5 to be dialed.Press “2” to not select phone/pager number 6 to be dialed. Press “1” toselect OGM1 to be delivered and press “2” to not select OGM2 to bedelivered. Press “1” to accept the channel configuration.STEP 11 Press “4” to program Channel 4. Press “1” to ENABLE.Press “2” twice to indicate no EXIT or ENTRY delay. Now press “1”for NORMALLY OPEN and the “2” for CONTINUOUS activation.Press “1” to select phone/pager number 1 to be dialed. Press “2” to notselect phone/pager 5 to be dialed. Press “1” to select phone/pagernumber 6 to be dialed. Press “2” to not select OGM1 to be deliveredand press “1” to select OGM2 to be delivered. Press “1” to accept thechannel configuration.STEP 12 Press “0” to exit PROGRAM: CHANNELS.Press “M” to exit programming mode .Sample Program Planner |
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved