6F8C1067model 3000 FA Control Network [FL-net (OPCN-2)]FL311/FL312 Module Operation Manual

Toshiba V Series Operation Manual

Overview

System Configuration

Network Configuration

Connection with Intelligent I/O Units

Connection to Engineering Tool

Storing User Data

Names and Roles of Products

CPU Module L1PU12H

Ethernet Module EN531

Terminal Block TB522

Loop I/O module LP01/LP03

Loop I/O module LP02/LP04

Loop Display Unit LD512H

AC power module PS591

Software Functions

Display function

Setting function

TOSLINE-S20LP message transmission

Setting Ethernet Module

Setting host IDs

Setting with Engineering Tool

Setting Network Parameters

Connection

Mounting and Removing Terminal Block Unit

Removing

Mounting and Removing Modules

Mounting EN531 on TB522

I/O Terminals

Connecting LD512H to Terminal Block

Terminal Block

Grounding

Ground bus

Withstand voltage test

Precautions for Wiring EN531T

Modules

Checking Switches

Start

Setting by Engineering Tool

Program Management

Troubleshooting

Trace Function

Protection Circuit

Daily Check

Maintenance and Inspection

Expendable Parts

Backup period

Module Replacement (EN531/EN531T)

A Table of Specifications

A.2 L1PU12H Hardware Specifications

A.3 EN531/EN531T Hardware Specifications

A.4 LP01 Hardware Specifications

A.5 LP02 Hardware Specifications

A.6 LP03 Hardware Specifications

A.7 LP04 Hardware Specifications

A.8 LD512H Hardware Specifications

A.9 PS591 Hardware Specifications

B.1 L1PU11H/L1PU12H Software Specifications

C External Views

D Trace Information

E Return Code List

Index

V Series

safety precautions

related manuals

Before Turning on the Power

functions and features

Checking the Content of the Package

Name and Function of Each Part

Installation Requirements

Power Requirements

Precautions when using

About the External FDD

Disposal

Installation

Installing Bases

Module Installation

Grounding method

Wiring of the power supply

chapter 2 installation

Connector Connection

Handling

Power Off with Windows

Power Supply module PS691 with UPS I/F

About the Hard Disk

Floppy Disk Handling

About the PC Card

Removal

Maintenance

Periodic Maintenance

Replacement Timing of Major Parts

Replacing the Hard Disk Drive

RAS Function

RAS Function Overview

Hardware Processing RAS Functions

Hardware Setup

Setting the BIOS

the mouse does not work

B Device Specifications

B.2 Interface Specifications

B.2.3 Keyboard and Mouse Interface

B.2.6 FDD Interface

B.2.7 PCMCIA card slot

Ethernet Module (EN311) Overview

Introduction

Standards and Terminology

S Controller

Basic Functionality

EN311 Specifications

Software Configuration

EN311 Parts and Functions

Outline Drawing

Dimensions and Components

Component Functions

LED Display

Preparing for Operation (Hardware)

Switch Settings

Mounting the EN311 in the Base Unit

Connecting to the Network

MAU Power Supply

Network Wiring Equipment

Preparing for Operation (Software)

Module Setup Flowchart (Software)

Registering the EN311

EN311 Operation Modes and Station Statuses

Function Block Specifications for EN311 Control

URCV_T function block

Socket Service Commands List

Error Status List

EN311 Reset (Reset Request)

Parameter Setup Request

Router IP Address Setup Requests

Operating Mode Control Requests

Initialization Sample Program

the PC Link Protocol Transmission

Computer Link Protocol Transmission

Sample Computer Link Protocol Program

PC Link Protocol Transmission (Data write)

PC Link Protocol Transmission (Data read)

Sample PC Link Protocol Transmission Program

Socket Interface Communication

EN311 Socket Interface Usage Notes

Data handling and data segmentation in TCP socket interface transmission and reception

Socket port numbers

UDP socket interface notes

Socket Interface Information

Using the EN311 Socket Interface

Sample Programs

TCP socket sample programs

RAS Information

Station Status Information

Down Information

Remote Station Verification Request

Time Setting

RAS Information Readout

Error Handling

Error Status

Station Status

Installation and Wiring

Power Supply Wiring and Grounding

Network Wiring

A Maintenance and Inspection

B Socket Service Command Table

C Error Status Table

Times

E Computer Link/PC Link Protocol Minimum Transmission Delay Times

Time

firmware

G.2 Revision K

G.3 Revision L

General

Names of Parts and their Functions

Setting

Switch Setting

Host ID setting switches (HOST-ID)

Operation mode setting switches (MODE)

Network Parameter Setting

Network ID and subnet mask setting

Station address (Host ID) setting

Multicast address summary

Setting with Engineering tool

Setting with Engineering Tool 2

Multicast address setting

Settings for multicast routing network

Ethernet link speed and duplex setting

Installation (Installing in the Base Unit)

Ethernet Cable Connection

BASE2 (EN631, EN641, EB641)

Drop Cable Connection for Line B Modules

VDC Power Cable Connection

Module Replacement

Operation

Check Before Operation

Inspection

Periodic inspection

Application Interface

Socket Information

Structure of dual Ethernet socket information

Socket information reference method

Toshiba V Series Operation Manual

Product

Learn More

Legal