E65821622. Installation and wiring 2-2Take special care with the installation environment of inverter. Install the inverter in a location that securesspace for ventilation and heat emitting, considering heat generation and occurrence of noise.2. 1. 1 Installation environmentThis inverter is an electronic control instrument. Take full consideration to install it in the proper operatingenvironment as follows. Installation environment• Operate in areas where ambient temperature rangesfrom –15°C to 50°C.Where ambient temperature will rise above 40°C,derating of rated current is needed. Refer to "InstructionManual for Load Reduction" (E6582116) for details.• Install the inverter in a well-ventilated place andmount it on a flat metal plate in portrait operation.• Leave a space of 10cm or more on the upper andlower sides of the inverter, and a space of 5cm ormore on each side.• This inverter have a structure with IP55 conformity.IP55 is a structure that protects the contents fromdust and harmful effects of water that drops fromevery direction.2. 1 InstallationWARNINGProhibited• Do not place any inflammable object near the inverter.If flame is emitted due to failure in the inverter, this will lead to fire.Mandatoryaction• Operate under the environmental conditions prescribed in the instruction manual.Operations under any other conditions will result in failure.CAUTIONProhibited• Do not install the inverter in any place with large vibration.The unit will fall due to the vibration, resulting in injury.5cm or more 5cm or more10cm or more10cm or moreVF-AS3

safety precautions

Read first

Indication of product type

Structure of equipment

Installation and wiring

Installation

How to remove covers of inverter

wiring,

standard connection diagram

Measures to satisfy standards

Compliance with UL/CSA standards

Compliance with safety standards

Selection and installation of peripheral devices

Selection of a wiring device

External option and insert type option

Table of parameters

Specifications

Outside dimensions and mass

Toshiba TOSVERT VF-AS3 Instruction Manual

Introduction

Product version

Overview

PROFINET

LED indicator

Diagnostic (PROFINET Service)

Hardware Setup

Wiring

Installation Topology

Parameters

Communication parameters for PROFINET

The details of the parameter setting

PROFIdrive Profile

STW Control Word Data

ZSW Status Word Data

State Machine

Vendor Specification Profile

Telegram 100: Vendor specific

Telegram 102: Vendor specific

The overview of the VF-S15/AS3 parameter

Access to the PROFIdrive parameter

PROFIdrive parameter (PNU)

Access to inverter parameter

PROFIdrive acyclic parameter access

Example2. Read the inverter parameter

Example3. Change the inverter parameter

Code Table for acyclic communication

Modbus TCP

x03) Read Holding Registers" function

x06) Write Single Register" function

x10) Write Multiple Registers" function

x2B) Read Device identification" function

Web server

Web pages structure

Drive parameters (Main menu: Monitoring)

Network parameters (Main menu: Network Setup)

Administration (Main menu: Network Setup)

TCP/IP statistics (Main menu: Diagnostics)

Activation of Java7

TOSVERT VF-AS3

pin assignment

functional description

industrial inverter

i safety precautions

maintenance and inspection

read first

Instruction Manual

operation panel

terminal blocks

installation environment

control terminals

display mode

language selection

contrast adjustment

increasing starting torque

Advanced] How to

jog run

bumpless operation

avoiding overvoltage trip

pid control

torque control

pattern operation

cooling fan control

adjustment parameters

communication functions

traverse function

monitoring operation status

monitor mode

Measures to satisfy

devices

peripheral devices

external options

emc filter

table of parameters

basic parameter

communication parameter

output terminal function

outside dimensions and mass

Maintenance and inspection

periodical inspection

instruction manual

specifications

outline drawing

standard connections

Multi-rating

led indicators

Operation procedure

installation and wiring

symbol

Basic operation] Operation panel and screen display

the symbol

copy function

Normal/emergency screen display

Basic operation] Operation methods of motor

To run/stop motor

Basic setting methods of parameters

Basic panel run methods

Basic terminal run methods

Fundamental operation] How to use parameters

Setting other basic parameters

Setting of extended parameters that are especially important

Input signals to the control terminals

Selecting terminal functions

Switching two to four types of motor characteristics

V/f 5-point setting

Setting the frequency commands

Setting the start and end frequencies

DC braking

Automatic stop when run continues at the lower limit frequency (sleep function)

Setting the preset-speed operation frequency

Avoiding trips

Single load sharing by multiple inverters (droop control)

Brake sequence

Switching to commercial power run

Retaining the stop position

Setting of motor parameters

Torque limits

Adjusting current and speed control gain

Setting the protection functions

Forced run control in emergency

Setting functions of operation panel

Trace function

Store cumulative power

Select EASY key function

Step-out detection of PM motor

My function

Applied operation by I/O signals

Frequency commands by the analog signals

Screen display at trip occurrence

Compliance with UL/CSA Standards

overload protection

Insert type options

Extended parameter

Advanced parameter

Communication parameter

Parameter setting range and default setting depending on capacity

Analog output/Monitor output function

Input terminal function

Setup menu

Guidance function

Trip information and measures

How to reset trip

If motor does not run while no trip message is displayed

In case of a failure

install the inverter

basic parameters

Display of Embedded Ethernet setting screen

Setting IP address

Communication parameters

Monitor parameters

The overview of the VF-AS3 command parameters

The overview of the VF-AS3 monitor parameters

x17) Read/Write Multiple Registers" function

Error Code

EtherNet/IP

Identity Object (0x01)

Message Router Object (0x02)

Assembly Object (0x04)

Connection Manager Object (0x06)

Motor Data Object (0x28)

Control Supervisor Object (0x29)

AC/DC Drive Object (0x2A)

Parameter access 1 Objects (0x64)

Parameter access 2 Objects (0x65)

Port Object (0xF4)

TCP/IP interface Object (0xF5)

Ethernet link object (0xF6)

Page structure of web server

Description for each

Toshiba TOSVERT VF-AS3 Instruction Manual

Product

Learn More

Legal