| 
TOSHIBA AC AdapterB-EP800-AC-QM-ROwner's Manual1Before using the unit, please read this manual thoroughly and retain it for futurereference.This symbol is intended to alert the user to the presence ofuninsulated “Dangerous voltage” within the product’senclosure that may be of sufficient magnitude to constitute arisk of electric shock to persons.This symbol is intended to alert the user to the presence ofimportant operating and maintenance (servicing) instructionsin the literature accompanying the appliance.NOTE:No user-serviceable parts inside. Refer servicing to qualified service personnel.Copyright © 2008by TOSHIBA TEC CORPORATIONAll Rights Reserved570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN< For EU Only >TOSHIBA TEC Europe Retail Information Systems S.A.Rue de la Célidée 33 BE-1080 BrusselsE PRINTED IN JAPANEO1-330827FM032900002<한국어><中文（繁體字）>CAUTION!Do not use this device for any devices other than the B-EP2DL or B-EP4DL seriesportable printer.PRÉCAUTIONS!N’utilisez pas ce dispositif pour une machine autre que les imprimantes portablesde la gamme B-EP2DL ou B-EP4DL.Achtung!Benutzen Sie dieses Netzteil für kein anderes Modell außer dem B-EP2DL oderdem B-EP4DL.ATENCIÓN!No utilice este adaptador para ningún otro dispositivo distinto a las impresorasportátiles B-EP2DL o B-EP4DL.WAARSCHUWING!Gebruik dit toebehoren uitsluitend met draagbare printers van de reeksen B-EP2DLof B-EP4DL.ATTENZIONE!Non utilizzare questo adattatore se non per la serie di stampanti portatili B-EP2DLo B-EP4DL .UWAGA!Nie należy używać tego urządzenia z urządzeniami innymi niż przenośne drukarkiserii B-EP2DL lub B-EP4DL.주의!포터블 프린터 B-EP2DL / B-EP4DL 시리즈 이외에는 사용 하지 말아 주십시오.注意!本機只適用与携帯型列印機B-EP2DL / B-EP4DL系列。ATENÇÃO!Não utilize este dispositivo para quaisquer outros dispositivos que não a série deimpressoras portáteis B-EP2DL ou B-EP4DL. .3CAUTION! (For customers in U.S.A. and Canada)1.To prevent electric shock, match wide blade of plug to wide slot, fully insert.2.To reduce the risk of hazards, use only CSA/UL Certified power cord set. Cord isTypeSPT-2 or heavier, minimum NO.18 AWG copper, one end is provided with amoulded-on male attachment plug cap (with a specified NEMA configuration),and the other end is provided with a moulded-on female connector body (with aspecified IEC non-industrial type configuration).CE Compliance (for EU only)This product complies with the requirements of EMC and Low Voltage Directivesincluding their amendments.NOTES:1.This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to Part 15 of the FCC rules. These limits are designedto provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses, and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the followingmeasures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.2.Changes or modification not expressly approved by manufacturer for compliancecould void the user’s authority to operate the equipment.“This Class B digital apparatus meets all requirements of the CanadianInterference-Causing Equipment Regulations. ”“Cet appareil numérique de la classe B respecte toutes les exigences duRèglement sur lematériel brouilleur du Canada.” (for CANADA only) |
