Toshiba 16N3KV2-E1 Installation Manual

Contents

480 100 18065 mm100 mmINDOOR UNITINDOOR UNITInstallation Place• Direct sunlight to the indoor unit’s wireless receiver should be avoided.• The microprocessor in the indoor unit should not be too close to RFnoise sources.(For details, see the owner’s manual.)Remote control• A place where there are no obstacles such as a curtain that may block thesignal from the indoor unit• Do not install the remote control in a place exposed to direct sunlight or closeto a heating source such as a stove.• Keep the remote control at least 1 m apart from the nearest TV set or stereoequipment. (This is necessary to prevent image disturbances or noiseinterference.)• The location of the remote control should be determined as shown below.Cutting a Hole and MountingInstallation PlateNOTE• When drilling a wall that contains a metal lath, wire lath or metal plate, be sureto use a pipe hole brim ring sold separately.Cutting a holeWhen installing the refrigerant pipes from the rearMounting the installation plateWhen the installation plate is directly mountedon the wall1. Securely fit the installation plate onto the wall by screwing it in the upperand lower parts to hook up the indoor unit.2. To mount the installation plate on a concrete wall with anchor bolts, use theanchor bolt holes as illustrated in the below figure.3. Install the installation plate horizontally in the wall.When installing the installation plate with a mounting screw, do not use theanchor bolt holes. Otherwise, the unit may fall down and result in personalinjury and property damage.1. After determining the pipe hole position on the mounting plate (¨), drill thepipe hole (Ø65 mm) at a slight downward slant to the outdoor side.• A place which provides the spaces around the indoor unit as shown in thediagram• A place where there are no obstacles near the air inlet and outlet• A place which allows easy installation of the piping to the outdoor unit• A place which allows the front panel to be opened• The indoor unit shall be installed as top of the indoor unit comes to at least2 m height. Also, it must be avoided to put anything on the top of the indoorunit.CAUTION54 °45°57 °(Side view) (Top view)Indoor unitReception rangeRemotecontrolRemotecontrolReceptionrangeIndoor unitThe center of the pipe holeis above the arrow.Pipe holeCAUTIONFailure to firmly install the unit may result in personal injury and propertydamage if the unit falls.• In case of block, brick, concrete or similar type walls, make 5 mm dia. holesin the wall.• Insert clip anchors for appropriate mounting screws 7.NOTE• Secure four corners and lower parts of the installation plate with 4 to 6mounting screws to install it.CAUTION7Installation plate(Keep horizontal direction.)5 mm dia. holeClip anchor(local parts)Mounting screwØ4 x 25RAnchor boltProjection15 mm or lessWiring ConnectionWiring of the connecting cable can be carried out without removingthe front panel.1. Remove the air inlet grille.Open the air inlet grille upward and pull it toward you.2. Remove the terminal cover and cord clamp.3. Insert the connecting cable (according to the local cords) into the pipehole on the wall.4. Take out the connecting cable through the cable slot on the rear panel sothat it protrudes from the front show on the figure below.5. Insert the connecting cable fully into the terminal block and secure ittightly with screws.6. Tighten firmly but not over 1.2 N·m (0.12 kgf·m).7. Secure the connecting cable with the cord clamp.8. Fix the terminal cover, rear plate bushing and air inlet grille on the indoorunit.How to connect the connecting cable• Be sure to refer to the wiring system diagram labeled inside the frontpanel.• Check local electrical cords and also any specific wiring instructions orlimitations.CAUTION17Anchor bolt holesHookHook HookPipe hole Pipe holeInstallationplateMounting screwWeightIndoor unitThread2 m or more from floor82.56217085