OneStart

Menu
Toro 07052 Operator's Manual Manual pdf 27 page image

Toro 07052 Operator's Manual

Also see for RAKE-O-VAC 07050: Operator's manualOperator's manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 preview
Contents
  1. Table Of Contents
  2. Introduction
  3. Safety and Instruction Decals
  4. Specifications
  5. Setup
  6. Mount Sweeper To Prime Mover
  7. Connecting Drive Shaft to Prime Mover PTO Shaft
  8. Before Operating
  9. Fill Fuel Tank
  10. Transport Hooks
  11. Adjust Rubber Flap
  12. Starting Instructions (Engine Driven)
  13. Stopping Instructions
  14. Maintenance
  15. Oil Drive Chain
  16. General Air Cleaner Maintenance
  17. Removing Debris From Engine
  18. Changing Rubber Flap
  19. Adjusting Belts
  20. Adjusting Drive Chain
  21. Changing Gear Box Oil
  22. Locking Collar Removal
  23. Thatcher Installation
  24. Flex Tip Rake Tine Replacement
  25. Changing Tires
  26. The Toro General Commercial Products Warranty
Toro 07052 Operator's Manual Manual pdf 27 page image
27Thatcher InstallationA 32 tooth jackshaft sprocket, a 19 tooth idler sprocket anda No. 60 chain make up the Thatcher Kit DriveComponents.1. Remove lower belt guard (Fig. 39) and reel drive belt(Fig. 40).2. Remove capscrew and washer securing jackshaft pulleyto jackshaft and remove pulley.12345Figure 471. Thatcher reel2. Reel support arm3. Jackshaft sprocket4. Idler sprocket5. Chain3. Slide 16 Tooth Jackshaft sprocket onto jackshaft.4. Secure by tightening two (2) set screws and lock nutson sprocket hub.5. Remove idler pulley presently on machine and replaceit with 19 tooth (#60) idler sprocket supplied withThatcher Kit.6. Slide Thatcher into position and secure to reel supportarms.7. Align idler sprocket with jackshaft sprocket andthatcher sprocket.8. Install No. 60 chain, included in kit. Lubricate withSAE 30 oil.9. Push down on idler sprocket until desired chain tensionis obtained.10. Fasten idler sprocket securely.Note: Spacers mounted on lift mechanism adjusting screwsmust be removed when thatcher is installed on machine.11. Put reel support arms in a lowered position.12. Remove jam nut and adjusting screw. Slide spacer offadjusting screw.132 45Figure 481. Spacer2. Adjusting screw3. Jam nut4. Pivot block5. Clevis13. Reassemble jam nut and adjusting screw with spacerpositioned on adjusting screw between pivot block andclevis. This is the storage position for spacer duringthatcher operation.14. Repeat procedure on other side of sweeper.Note: Spacers should be re–installed whenever the thatcheris removed and either the brush or flex tip reel is mountedto sweeper.Flex Tip Rake Rod Or FingerPlate Replacement1. Remove capscrew and locknut from one end of reel.2. Remove locknut only, from opposite end of reel.3. Drive rod from end plate. Drive rod from end withoutthe tab welded to it.4. Remove finger plates or rods as required and replace.5. Line up finger plate with rod and drive rod backthrough end plate.6. Attach capscrew and locknuts and hook up springs.
/ 32
Related manuals for Toro RAKE-O-VAC 07050
Toro 07081 Operator's Manual first page preview
Toro 07081 Operator's Manual
Toro 30426 Operator's Manual first page preview
Toro 30426 Operator's Manual
This manual is suitable for:
RAKE-O-VAC 07050RAKE-O-VAC 07052
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved