Sony KLV-V26A10E Service Manual

Also see for Bravia KLV-V26A10E: Service manual Operating instructions

- 23 -AT2XRM-EA001/RM-ED001METI DRADNATSBC_TUPNI_WP 2-+012METI DRADNATSRC_TUPNI_WP 2-+012Service adjustments to this model can be performed using thesupplied remote Commander RM-EA001 or RM-ED001.3. Press ‘MENU’ on the remote commander to obtain the followingmenu on the screen.4. Move to the Service icon using the up or down arrow button onthe remote commander5. Press the right arrow button to enter into the required menu item.6. Press the ‘Menu’ button on the Remote Commander to quit theService Mode when all adjustments have been completed.Note :• After carrying out the service adjustments, to prevent thecustomer accessing the ‘Service Menu’ switch the TV set OFFand then ON.1. Turn on the power to the TV set and enter into the stand-bymode.2. Press the following sequence of buttons on the RemoteCommander.SECTION 3 SET-UP ADJUSTMENTS3-1. How to enter Service Mode3-2-1. Check AD (CCPX case) calibrationregistration items.(Also see 3-2-1(a))This adjustment is done using ECS.1. Select AV1 and input PAL signal.2. Change the TV Picture Mode to 1 (Custom).3. Set the following registration items.3-2. Signal Level Adjustment(Also see 3-2(a))Y_NI_WP_TEGRAT 512DNABDAED_Y_JDA 2NETTAPOOL_Y_JDA 01C_NI_WP_TEGRAT 512DNABDAED_C_JDA 2NETTAPOOL_C_JDA 01TUO_EMIT_JDA_DA 8213-2-2. Y signal AD calibration of CCPX decode.(Also see 3-2-2(a))1. Check “TIMING_INDEX”=5 (AV_CVBS_PAL).2. Input 0 IRE black full field with burst.3. Send “READ_PW_INPUT_Y” command from ECS.4. Check that the detection value of “PW_INPUT_Y” is within thestandard below.METI DRADNATSY_TUPNI_WP 5-+615. Input 100 IRE white full field with burst.6. Send “ADJUST_Y_LEVEL_VIDEO” command from ECS.The CP13_CVBS_Y_LEV registration of the video range isadjusted automatically by this commandAdjustment value is also copied in to the proper NVM area.7. Check that the detection value of “PW_INPUT_Y” is within thestandard below.METI DRADNATSY_TUPNI_WP 5-+5123-2-3. C signal AD calibration of CCPX decode.(Also see 3-2-3(a))1. Check “TIMING_INDEX”=5 (AV_CVBS_PAL).2. Input 0 IRE black full field with burst.3. Send “READ_PW_INPUT_Y” command from ECS.4. Check that the detection value of “PW_INPUT_Y” is within thestandard below.METI DRADNATSBC_TUPNI_WP 5-+8215. Input blue full field with burst.6. Send “ ADJUST_C_LEVEL_VIDEO” command from ECS.i+ 5 +(ON SCREEN (DIGIT 5) (VOLUME +) (TV)DISPLAY)I/TVThe CP14_CVBS_C_LEV registration of the video range isadjusted automatically by this commandAdjustment value is also copied in to the proper NVM area.7. Check that the detection value of “PW_INPUT_CB” is withinthe standard below.8. Input red full field with burst.9. Send “READ_PW_INPUT_CR” command from ECS.10. Check that the detection value of “PW_INPUT_CR” is withinthe standard below.