Sony HMZ-T1 Startup Manual

Also see for HMZ-T1: Reference guide Specifications Limited warranty Notes Startup guide

1 Connect a playback equipment and a TV.3 Connect the mains lead and plug it in.2 Connect the head mounted unit.Head mounted unitProcessor unit (Front)Enjoy Video in Four StepsBy design, the system will offer an impressive experience only after you takea moment to adjust it to fit you well. Confirm the following steps and preparefor use before enjoying content with this system.1 Connect2 Wear Adjust the head mounted unit correctly.Adjust the head mounted unit securely to your head, so that thedisplay stays directly in front of your eyes.3 Set Up Adjust the lens span correctly.The distance betweenthe centres of the pupilsWide NarrowThe distance between pupils varies from person to person. Wear thehead mounted unit correctly and adjust the lens span to the correctwidth to align images on the left and right lenses and form images.4 EnjoyWhat’s in the boxHead mounted unit Processor unit HDMI cable (1) Accessories Mains lead (1)Head Mounted DisplayStartup GuideHMZ-T1Before use, also refer to “Health Precautions” and“Precautions” in the “Reference Guide.”4-297-825-61(1)1 ConnectHDMIINTVHDMIOUTBlu-ray DiscTM playerGame consolePlayback EquipmentProcessor unit (Back)4 Turn the playback equipment on.© 2011 Sony Corporation Printed in JapanIf your playback equipment has only oneHDMI OUT jack and you also want towatch content from it on a TV, connect itto the processor unit with the suppliedHigh-Speed HDMI cable, and connectthe processor unit to the TV with anotherHigh-Speed HDMI cable (recommendedcable length: up to 5 m).Notes Make sure to set “HDMI pass-through” to“On” in the “General Setup” menu whenconnecting a TV or other display device. Make sure that the system is in standbymode when watching content on aconnected TV or other display device.HDMI cable (supplied)To mainsAdjustable Parts Top headband strap Bottom headband strap Headband, release buttonIf you normally wear glasses or contact lenses, wear them as usual during use (with the exception of readingglasses). Note that watching with bifocals may be less than optimal.1 Pull out the headband.On one side after another, hold the band release buttondown and loosen the headband.2 Turn the system on ().The power indicator on the processor unit is nowlit in green.3 Bring the headband strap down aroundthe back of your head.Lower the bottom headband strap to the base of your head.4 Straighten the uniton your head.Straighten the front of the unit, sothat it is not tilted downward.5 Tighten the headband gently.Gently tighten the headband, evenly on both sides. If the topor bottom headband strap is too loose, adjust the length.6 Adjust the position on your head.Carefully adjust the unit left and right (and up and down, asneeded) to find the best position for viewing the centre ofthe screens.7 Tighten the headband securely. Support the unit with both the forehead supporter andthe bottom headband strap. Do not support the unitwith the bridge of your nose. Fasten it to keep it level on your head.Note If the unit tips forward, lower the bottom headband strap tobalance the unit on your head.8 Adjust the headphones.Move the headphones forward, back, up, or down to positionthem over your ears.1 Select a display language (first timeonly).Press the / button to select alanguage, and then press the MENU or button.2 Adjust the lens span.Hold the lens span adjusters on both sides and slidethem together until you can see the screen clearly. Afteradjustment, press the MENU button or  button.Note If you cannot see the screen clearly after lens spanadjustment, start over from “2 Wear.”3 Check display alignment.Confirm that all three “” marks and the horizontal lineintersect, and then press the MENU or  button.It is acceptable if the “” marks and the horizontal lineintersect in a position other than the centre of the screen.Note If even one of the “” marks and the horizontal line donot intersect, stop using the system. For details, see the“Reference Guide.”4 Follow the instructions displayed.After reading the information, press the MENU or button.All three “” marks and the horizontalline intersect.More than one of the “” marks and thehorizontal line do not intersect.Control playback from compatible playback sources.Controlling Playback from the UnitFor details on configuring menu settings and attaching accessories, see the“Reference Guide.”2 Wear Wearing the unit will prevent you from seeing outside the display. Before you put it on, take a moment to review steps 2 – 4(Wear, Set up, and Enjoy), so that you know the sequence of operations.3 Set Up Follow the instructions displayed on thescreen for operations. 4 EnjoyTo remove the head mounted unitHold the band release buttons on both sides and pull the unitforward as you lift it off.Notes The system cannot be used for advancedplayback equipment control, such as menuoperations. Control using these buttons is only possiblewhen the “Control for HDMI” in “General Setup”is set to “On” (default setting). Some playback equipment cannot becontrolled using the head mounted unitbuttons.PlayFast-forwardHold the button down to jumpto the next chapter.PausePower on/standbyHold the button down toenter standby mode.Fast-rewindHold the button downto jump to the previouschapter.VolumeGBCT

/ 2

Related manuals for Sony HMZ-T1