Sony DMX-NV1 Quick Setup Guide (For DMX-NV1 model sold separately) Quick Setup Manual

Also see for BRAVIA DMX-NV1: Operating instructions Operating instructions Quick setup guide Specifications Specifications

Contents

package contents

NETWORK VIDEO RECEIVER Quick Setup GuideDMX-NV1© Sony Corporation 2007. Printed in USA. 3-216-111-11(2)Package Contentsz Remote control not supplied. To operate this receiver, use your TV’s remotecontrol equipped with the DMeX button.z Ethernet cable required (not supplied).z Using your PC, view the Operating Instruction Manual on the Internet athttp://internet.sony.tv/manualAC Adapter withAC Power CordStandWarranty Card Attachment GuideQuick Setup GuideNETWORK VIDEO RECEIVER Quick Setup GuideDMX-NV1© Sony Corporation 2007. Printed in USA.3-126-111-11(1)Receiver (DMX-NV1)& Cable Cover Mounting BracketMounting Knobs Screws, Type 1 Screws, Type 2USB CableHDMI CableSetting up the BRAVIATM Internet Video Linkz If you need to configure a fixed IP address or proxy server, check the Operating Instruction Manual for more information.POWERPORT 1 PORT 2 PORT 3 PORT 4Gaming Adapter as Wireless BridgeEthernet CablePOWERPORT 1Wireless RouterGamingAdapterPowerline Ethernet AdapterEthernet CablePOWERPORT 1 PORT 2 PORT 3 PORT 4Ethernet CableExis ting Electrica l Wiri n gRouterPowerlineEthernetAdapterPOWERPORT 1 PORT 2 PORT 3 PORT 4Direct to RouterEthernet CableRouterPOWERINTERNETModemA DC IN 9V: Connect the AC adapter to this port. Do notplug into the wall outlet at this time.B DMex: Connect the small end of the USB cable to thisport.C LAN: Connect an Ethernet cable (not supplied) to thisport.D HDMI OUT: Connect the L-shaped end of the HDMI cableto this port.The BRAVIATM Internet Video Link receiver is compatible with certain Sony televisions with the XMBTM(XrossMediaBar®) and DMeX interface. High-speed Internet access is also required.Power off your TV before beginning the setup. The receiver can be installed either as a stand-alone or mounted to the back of your TV set.OUTLANDC IN 9VNETWORKINPUTSERVICE% $ #"OUTLAN DC IN 9VOUTLAN DC IN 9VFront ofReceiverz The rear view and location of the ports as shown may differ from your TV set.OUTLAN DC IN 9V% $ # "B1 Remove Cable CoverRemove the cable cover to expose the portslocated on the bottom of the receiver.Please read all instructions before beginning the installation.Refer to the separate Attachment Guide for instructions on attaching to your TV.BOUTLAN DC IN 9V%#HDMIDMexNETWORKPower LEDNetwork LEDInternetVideo IconNetwork IconVideo IconMedia Category Bar2 Connect CablesConnect the cables in the order shown below.3 Connect to TVB Connect the large end of the USB cableto the DMe X/SERVICE port on the TV.D Connect the straight end of the HDMI cableto any HDMI port on the TV.4 Connect to the InternetConnect an Ethernet cable to your Internet source by choosing one of the following recommendations for easy “plug and play.” Your receiver will automatically attempt toconnect to the Internet.5 Verify Connectiona. Plug in the receiver and power on the TV.b. Once the receiver and TV are powered on,confirm the LED lights.Standard Definition video: 802.11gHigh Definition video: 802.11nStandard Definition video: HomePlug Turbo,HomePlug AV, UPA, HD-PLCHigh Definition video: HomePlug AV, UPA, HD-PLC6 Confirm ConnectionFollow these instructions to confirm.a. Press the DMeX button on your TV’s remote controlto view the connection status.z If “Feature available with DMeX module” appears on thescreen, wait a few moments and try again.b. When you see the message “Configuration Successful,”press the HOME button on your TV’s remote control.These menu icons associated with the receiver will appearon the XMBTM (XrossMediaBar®).z IMPORTANT: Do not press the INPUT button on theremote control to access the BRAVIA™ Internet VideoLink. It is available on the XMBTM.7 Enter RegionIt is strongly recommended that you completeRegion Setup before using your receiver.a. Highlight the Internet Video icon at the bottom of theSettings menu on the XMBTM (XrossMediaBar®) andpress .b. Highlight Region and press .c. Follow the on-screen instructions to complete the setup.z Default country is the United States. Press the B buttonto select a different country.8 Attach Cable CoverSlide the cable cover back into place.BOUTLAN DC IN 9VOUTLAN DC IN 9VFront ofReceiverz For attachment options to the TV, see the separateAttachment Guide.When you see... Receiver...PowerLEDGreen is powered “On.”Red is not connected. Check all cablecomponents.Orange is in update mode.NetworkLEDGreen is connected to the Internet.BlinkingGreenhas network activity.

/ 2

Related manuals for Sony BRAVIA DMX-NV1