Sony CLIE PEGA-MD700 Operating Instructions Manual

Also see for CLIE PEGA-MD700: User guide Declaration of conformity Supplementary guide

Contents

Initial Setup• When you use the PEG-S300/U, the following setting is necessary.• If you use the PEG-N710C/U, the following setting is unnecessary. It is recommended tochange the setting of “Init String:” in accordance with the country where of use.1 Select “Prefs” in the System screen.2 Tap V at the upper right corner on the“Preferences” screen of the CLIÉ handheld,and select “Connection.”3 Select “New...,” and choose “Details...” on the “Edit” screen.4 Tap V in “Speed:” and select “57,600 bps”from the list.5 Enter “AT&FX4” in “Init String:.”If you have trouble connecting to the internet,enter “AT&F+GCI=B5” next-line “ATX4.”This unit is factory set for the initializationcommand in the USA. Sony recommends setting inaccordance with the table below:USA and Central/South America, China and other(FCC):“AT&F+GCI=B5” next-line “ATX4”Japan:“AT&F+GCI=00” next-line “ATX4”EU and other (CTR21):“AT&F+GCI=B4” next-line “ATX4”If you use CLIÉ MODEM in office and hotel with PBX telephone system, Sony suggestto change AT command “ATX4” to “ATX3,” which means “(normal dialing)” to “(nodetect dial tone).”6 Select “OK.”This brings you back to the “Edit” screen.7 Configure the following settings on the“Edit” screen.“Name:” Please change the pre-set name“Custom” to a name which you caneasily recognize. Of course, it canremain as “Custom.”“Sony CLIÉ Modem” will be used inthis example.“Connection Method:”This should remain as “Serial toModem.”“Dialing:” This should remain as “TouchToneTM.”“Volume:” No volume output at any setting.Please change according to your preference.8 Tap “OK” on the “Edit” screen.This brings back you to the “Preferences” screen,and “Sony CLIÉ Modem” will be listed underAvailable Configurations.9 This concludes the connection procedure. Now please follow the steps inConfiguring Network Settings.WARNINGTo prevent fire or shock hazard, do not expose the unit to rain or moisture.To avoid electrical shock, do not open the cabinet. Refer servicing to qualifiedpersonnel only.Owner’s RecordThe model and lot numbers are located on the bottom of CLIÉ MODEM. Record the lotnumber in the space provided below. Refer to the model and lot numbers when you callyour Sony dealer regarding this product.Model No. PEGA-MD700Lot No.This equipment complies with Part 68 of the FCC rules. On the bottom of this equipment isa label that contains, among other information, the FCC Ringer Equivalence Number(REN) for this equipment. If requested, this information must be provided to the telephonecompany.This modem uses the USOC RJ-11 telephone jack.The REN is used to determine the quantity of devices which may be connected to thetelephone line. Excessive RENs on the telephone line may result in the devices not ringingin response to an incoming call. In most, but not all areas, the sum of the RENs should notexceed five (5.0). To be certain of the number of devices that may be connected to the line,as determined by the total RENs, contact the telephone company to determine themaximum REN for the calling area.If the terminal equipment causes harm to the telephone network, the telephone companywill notify you in advance that temporary discontinuance of service may be required. Butif advance notice is not practical, the telephone company will notify the customer as soonas possible. Also, you will be advised of your right to file a complaint with the FCC if youbelieve it is necessary.The telephone company may make changes in its facilities, equipment, operations orprocedures that could affect the operations of the equipment. If this happens, thetelephone company will provide advance notice in order for you to make the necessarymodifications in order to maintain uninterrupted service.If trouble is experienced with this equipment, you can reach the Sony CustomerInformation Service Center at 1-877-760-SONY or find Sony Customer Service on the webat http://www.sony.com/peg/support/.Repair of this equipment should be made only by a Sony Customer Information ServiceCenter, call 1-877-760-SONY (1-877-760-7669).This equipment cannot be used on public coin service provided by the telephone company.Connection to Party Line Service is subject to state and possible provincial tariffs. (Contactthe state or provincial utility service commission, public service commission, orcorporation commission for information.)You are cautioned that any changes or modifications not expressly approved in thismanual could void your authority to operate this equipment.This MODEM can connect and use AC adapter of CLIÉ handheld.The socket-outlet shall be installed near the equipment and shall be easily accessible.• CLIÉ is a trademark of Sony Corporation.• HotSync is a registered trademark, and the HotSync logo is a trademark of Palm, Inc. orits subsidiaries.• Microsoft ® and Windows® are registered trademarks of Microsoft Corporation in theUnited States and/or other countries.• All other trademarks are trademarks of their respective owners.Before useThe MODEM for CLIÉ Handheld is designed for use with the Sony CLIÉ handheld,personal entertainment organizer series. You can connect to the internet via a regularphone line by connecting your Sony CLIÉ handheld to this CLIÉ MODEM using thesupplied cable to connect to a modular jack.You can also charge the battery of your CLIÉ handheld using the AC adapter of this unit inthe same way you use the cradle. And you can synchronize (HotSync ®) data between theCLIÉ handheld and your computer by using the USB cable.CLIÉ MODEM can be attached with both type of CLIÉ handheld, PEG-300, 700 series bycommon attachment structure.4-653-154-11 (2)MODEM forCLIÉ HandheldOperating InstructionsSony Corporation © 2001 Printed in TaiwanPEGA-MD700Location of controlsInserting the batteriesInsert the batteries as illustrated.To operate the unit without batteries, connect the AC adapter to a wall outlet. For detailsabout how to connect the AC adapter, see Step 1 in “Charging the CLIÉ handheld.”TipsContinuous access for sending and receiving data by new Alkali AAA batteries can beworked over 100 minutes without battery change. Use same type of battery. Prefer SONYAlkali AAA battery. Do not mix use old (spent) one and new (deferent spending time) one.Connect the CLIÉ handheld to the CLIÉMODEMConnect the CLIÉ handheld to this unit as illustrated.Connecting to the internet1 Connect the modular cable.2 Turn on the CLIÉ handheld.3 Operate according to the operating instructions of the CLIÉhandheld.Notes• If AAA batteries are not inserted, AC adapter is necessary to be connected.• The CLIÉ MODEM has the function that automatically shut down its power after2 minutes without any sending and receiving data during internet connecting.Place the CLIÉ handheldon this unit.Connect to the modular jackon the wall.Connect the modular cableto the modular jack.Two size AAA (LR03) batteries(not supplied)1 Battery compartment(located on the back of the unit)2 DATA indicatorLit up:The power supply is on.Quickly flashing (Approx. 8 times persecond):Dialing.Slowly flashing (Approx. 2 times persecond):Sending and receiving data.3 EXT Power indicatorThe indicator lights up while the CLIÉhandheld acts in the condition where the ACadapter and CLIÉ handheld were connectedto this unit or during charging.4 AC adapter connector5 Interface connector6 HotSync button7 USB connector8 Modular jack

/ 2

Related manuals for Sony CLIE PEGA-MD700