Sony BVMF170A Operation Manual

Also see for BVM-F250: Manual Operation manual Operation manual Operation manual

Contents

108 Specifications (BVM-F170A)AppendixesColor space (color gamut)ITU-R BT.709, EBU, SMPTE-C, F170Native2)2) The BVM-F170A individual chromaticity points.The widest color space setting of the signalreproduced by the BVM-F170A(Typical)Warm-up time Approx. 30 minutesInputSDI BNC (×2)Input impedance: 75 ohms unbalancedSignal formatSee “Available Signal Systems”(page 112) and “Available SignalFormats” (page 113).Sampling frequency3G-SDI:Y/Cb/Cr (4:2:2)148.5MHz/74.25MHz/74.25MHzY/Cb/Cr (4:4:4)148.5MHz/148.5MHz/148.5MHzG/B/R (4:4:4)148.5MHz/148.5MHz/148.5MHzHD-SDI:Y/Cb/Cr (4:2:2)74.25MHz/37.125MHz/37.125MHzSD-SDI:Y/Cb/Cr (4:2:2)13.5MHz/6.75MHz/6.75MHzQuantization3G-SDI: 10 bit/sample, 12 bit/sampleHD-SDI: 10 bit/sampleSD-SDI: 10 bit/sampleHDMI HDMI (×1)HDCP correspondence, Deep ColorcorrespondenceSignal formatSee “HDMI/DisplayPort” (page 118)of “Available Signal Formats”.DisplayPort DisplayPort connector (×1)HDCP correspondence, 18/24/30bpp(bits per pixel) correspondenceSignal formatSee “HDMI/DisplayPort” (page 118)of “Available Signal Formats”.Option port Four (4) portsSignal formatSee “Available Signal Systems”(page 112) and “Available SignalFormats” (page 113).Parallel remote D-sub 9-pin (female) (×1)Serial remote (LAN)Ethernet (10BASE-T/100BASE-TX),RJ-45 (×1)OutputSDI BNC (×1) (monitor output)Output signal amplitude:800 mVp-p±10%Output impedance: 75 ohms unbalancedTransmission distance3G-SDI: 70 m max. 3)HD-SDI: 100 m max.3)SD-SDI: 200 m max.4)The signal from the monitor outputconnector does not satisfy the ON-LINEsignal specifications.3) When using the 5C-FB coaxial cable made byFujikura Ltd. or equivalent4) When using the 5C-2V coaxial cable made byFujikura Ltd. or equivalentDC 5V OUT Circle 4-pin (female) (×1)GeneralPower requirements100 V to 240 V AC,1.2 A to 0.7 A, 50/60 Hz24 V to 28 V DC,4.5 A to 3.9 APower consumptionApprox. 110 W (AC power supply)/approx. 100 W (DC power supply)(maximum)Approx. 60 W (AC power supply)/approx. 60 W (DC power supply)(average power consumption in thedefault status)Inrush current (1) Maximum possible inrush current atinitial switch-on (Voltage changescaused by manual switching):55 A peak, 15 A r.m.s. (240V AC)(2) Inrush current after a mainsinterruption of five seconds (Voltagechanges caused at zero-crossing):36 A peak, 7 A r.m.s. (240V AC)Operating temperature0 °C to 35 °C (32 °F to 95 °F)Recommended: 20 °C to 30 °C (68 °F to86 °F)Operating humidity0% to 90% (no condensation)Storage/transport temperature–20 °C to +60 °C (–4 °F to +140 °F)x yR 0.681 0.319G 0.189 0.724B 0.141 0.051Note