OneStart

Menu
Siemens SITRANS LG270 Operating Instructions Manual Manual pdf 61 page image

Siemens SITRANS LG270 Operating Instructions Manual

Also see for SITRANS LG270: Operating instructionsOperating instructionsOperating instructionsOperating instructions

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 previewPage 36 previewPage 37 previewPage 38 previewPage 39 previewPage 40 previewPage 41 previewPage 42 previewPage 43 previewPage 44 previewPage 45 previewPage 46 previewPage 47 previewPage 48 previewPage 49 previewPage 50 previewPage 51 previewPage 52 previewPage 53 previewPage 54 previewPage 55 previewPage 56 previewPage 57 previewPage 58 previewPage 59 previewPage 60 previewPage 61 previewPage 62 previewPage 63 previewPage 64 previewPage 65 previewPage 66 previewPage 67 previewPage 68 previewPage 69 previewPage 70 previewPage 71 previewPage 72 previewPage 73 previewPage 74 previewPage 75 previewPage 76 previewPage 77 previewPage 78 previewPage 79 previewPage 80 previewPage 81 previewPage 82 previewPage 83 previewPage 84 previewPage 85 previewPage 86 previewPage 87 previewPage 88 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. About this document
  4. For your safety
  5. EU conformity
  6. Product description
  7. Principle of operation
  8. Packaging, transport and storage
  9. Mounting
  10. Mounting instructions
  11. Connecting to power supply
  12. Connecting
  13. Wiring plan, double chamber housing
  14. Supplementary electronics
  15. Switch-on phase
  16. Set up with the display and adjustment module
  17. Adjustment system
  18. Parameter adjustment - Quick setup
  19. Saving the parameterisation data
  20. Setup with PACTware
  21. Parameter adjustment with PACTware
  22. Set up with the quick setup
  24. Set up with other systems
  25. Diagnostics and servicing
  26. Status messages
  27. Rectify faults
  28. Exchanging the electronics module
  29. Exchange or shorten cable/rod
  30. Software update
  31. How to proceed if a repair is necessary
  32. Dismount
  33. Supplement
  34. Dimensions
  35. Trademark
Siemens SITRANS LG270 Operating Instructions Manual Manual pdf 61 page image
61PBD-51041064 SITRANS LG270 - Operating Instructions44293-EN-171021CodeText mes-sageCause Rectification DevSpec State in CMD 48S603Impermissibleoperating volt-age• Operating voltage belowspecified range • Check electrical connection• If necessary, increase oper-ating voltageBit 11 of Byte 14 … 24The following table shows the error codes and text messages in thestatus message "Maintenance" and provides information on causesas well as corrective measures.CodeText mes-sageCause Rectification DevSpec State in CMD 48M500Error in the de-livery status• The data could not berestored during the reset todelivery status• Repeat reset• Load XML file with sensordata into the sensorBit 0 of Byte 14 … 24M501Error in thenon-activelinearisationtable• Index markers are not con-tinuously rising, for exampleillogical value pairs• Check linearisation table• Delete table/Create newBit 1 of Byte 14 … 24M504Error at a de-vice interface• Hardware defect • Exchanging the electronics• Send instrument for repairBit 4 of Byte 14 … 24M505no measuredvalue avail-able• Sensor does not detect anecho during operation • Check and correct mountingand/or parameter adjustmentBit 5 of Byte 14 … 24• Process component or probecontaminated or defective • Clean or exchange processcomponent or probeM506Installation/Setup error• Error during setup • Check and correct mountingand/or parameter adjustment• Check probe lengthBit 6 of Byte 14 … 24M507Error in theinstrumentsettings• Error during setup• Error when carrying out areset• False signal suppressionfaulty• Carry out reset and repeatsetupBit 7 of Byte 14 … 249.4 Rectify faultsThe operator of the system is responsible for taking suitable meas-ures to rectify faults.The first measures are:• Evaluation of fault messages via the adjustment device• Checking the output signal• Treatment of measurement errorsMaintenanceReaction when malfunc-tion occursProcedure for fault recti-fication
/ 88
Related manuals for Siemens SITRANS LG270
Siemens SITRANS LR 300 Instruction Manual first page preview
Siemens SITRANS LR 300 Instruction Manual
This manual is suitable for:
SITRANS LG270
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved