Sharp PN-V600A Operation Manual

Also see for PN-V600A: Brochure & specs Setup manual Setup manual

21 ERemote Control ModeWith the remote control unit it’s possible to perform operationof...• The primary monitor• Monitors with a specified ID No.• All primary/secondary monitorsIt’s necessary to specify which type of operation will beperformed in advance.1. If using the remote control unit, press MODE for approx 5seconds.If using the monitor buttons, hold both and atthe same time on the primary.▲▲THIS MONITOR ONLYREMOTE CONTROL MODEMODEOK CANCELOperate this monitor.2. Press or , select the mode, then performsettings.THIS MONITOR ONLYPerforms operation of only the primary using the remotecontrol unit.[Example] If the volume is lowered, the volume of the primarywill lower.SecondaryID No.: 2SecondaryID No.: 3PrimaryID No.: 1SecondaryID No.: 4VOLUME 10Press to lower the volumeSPECIFIED MONITORPerforms operation of a monitor with a specified ID No. usingthe remote control unit.Press or to select ID No., then press or toselect the ID No. of the monitor that you will operate.* When it receives signals from the remote control unit,“Operating specified monitor.” will be displayed on theprimary screen.[Example.] If ID No. is set to 3 and the volume is lowered,the volume of the monitor for ID No.: 3 will lower.SecondaryID No.: 2SecondaryID No.: 3PrimaryID No.: 1SecondaryID No.: 4VOLUME 10Press to lower the volumeWhen you would like to confirm the ID No. that is set to themonitor, press or to select ID No. DISPLAY, thenpress . The ID No. will be displayed on the screen.ALL MONITORSPerforms operation of all primary/secondary monitors.* ALL will be displayed on the menu of the primary.* When it receives signals from the remote control unit,“Operating all monitors.” will be displayed on the secondaryscreen. (Excluding power and input mode selection operation)* Settings may not be reflected depending on the state of theconnected monitors.[Example] If the power for the primary is turned ON, the powerfor all the monitors will be turned ON.SecondaryID No.: 2SecondaryID No.: 3PrimaryID No.: 1SecondaryID No.: 4Power ON Power ONPower ONPower ONPress to turn the power ONPOWERPress or to select EXPAND ITEM, and press orto select to perform this action or not.OFF ...........For all monitors, only power, input modeselection, and product information displayoperations will be recognized.ON .............For all monitors, all operations will berecognized.After returning to the normal screen withprocedure 3, when 5 minutes have passed fromthe end of operation, it will automatically returnto OFF.ALL [EXPAND ITEM] will be displayed on the menu ofthe primary.* Even when REMOTE CONTROL MODE is setto ALL MONITORS, certain settings such asLAN settings and ID No. settings will not bereflected on the other monitors.3. Press or to select OK, then press MENU andreturn to the normal screen.4. Perform operation.Caution• When the remote control mode is set to ALL MONITORSand EXPAND ITEM is set to ON, performing remote controloperations that change adjustment values will result inthe secondary adjustment values being the same as theprimary adjustment values.SecondaryID No.: 2SecondaryID No.: 3PrimaryID No.: 1SecondaryID No.: 4SecondaryID No.: 2SecondaryID No.: 3PrimaryID No.: 1SecondaryID No.: 4VOLUME 12 VOLUME 11VOLUME 10VOLUME 9VOLUME 10 VOLUME 10VOLUME 10VOLUME 10Press to lower the volumeBe careful of this when adjusting individual displays.TIPS• You can copy the setting values of the primary to othermonitors with COPY SETTING VALUE. (See page 25.)• The buttons on the monitor itself (primary) are also effectivein remote control mode.• When monitors connected in a daisy chain are in standbymode for LOW POWER, operation cannot be performed forsubsequent monitors.